Question about 2001 Volkswagen Golf

4 Answers

Vw golf 1.4 16v after changeing timing belt car idles eratticaly or not at all. Timing marks correct at crankshaft, cam pulleys locked as per haynes manual!

Posted by on

  • Anonymous Mar 26, 2014

    cant find the crankshaft timing marks. engine tore down by someone else

×

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

The timing could be 180 degrees out you will have to do it all over again. Bring #1 cylinder upto TDC check the distributor rotor arm that it is pointing to #1 plug wire, It is important that the cams are on the intake stroke and not on the exhaust stroke. The crank is no big deal just make sure the marks are lined up.

Posted on Sep 10, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Do u have vals 4 1998 vw golf 2,0 motor

Posted on Nov 10, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Hallo
I think if your timing is ok, clean throttle body. this will fix your problem.
marko

Posted on Sep 10, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did you check the timing? Using a timing light and the number one spark plug wire, does the light light the timing mark? If it will not run to check then you must remove all four spark plugs and hand crank the engine until both valves are closed in the number one cylinder and the piston is at top dead center. This is where the number one spark plug should fire with zero spark advance. With both valves closed and the piston at top dead center, the timing mark should be under the pointer, exactly. If not, you have a timing issue.

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt broke there are no marks on cam gear,s at all how to re align cam gears on tdc


The crankshaft pulley keyway is to be set to 11 o'clock for TDC of no. one piston. Follow the diagram on page 2B-9 of the Haynes Manual for the camshaft timing marks!

Apr 09, 2015 | 2001 Mazda Tribute

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

How do i replace the timming belt on a 1996 vw glof 2.0


if you havn' t done it before best to get an experienced technician to do it. [critical part, can cause major damage if incorrectly fitted]. before removing belt line up timing mark on crankshaft pulley with arrow on timing belt cover. remove inspection plug on top of gearbox bell housing. v cut away on fly wheel should be lined up with notch on g/box housing. timing mark on inside of camshaft pulley must line up with top of cylinder head surface at front of head. if distributor fitted, remove cap . rotor should be pointing to mark on distributor housing. remove old belt, fit new keeping timing marks in same positions. tension cambelt. should be able to turn belt 90 degrees side ways between cam pulley and intermediate pulley if tension is correct. reset ignition timing on completion.

May 20, 2010 | 1996 Volkswagen Golf

1 Answer

Fixing the timing belt


  1. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch on the crankshaft pulley should align with the dot on the intermediate shaft sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.

To install:
  1. Check the alignment of the timing marks. On 16 valve engines, the mark on the tooth should align with the mark on the rear belt cover.
  2. Install the new timing belt and tension the belt so it can be twisted 90 ° at the middle of it's longest section, between the camshaft and intermediate sprockets.
  3. Recheck the alignment of the timing marks and, if correct, turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck belt tension and timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45 Nm).
  4. Install the belt cover and accessory drive belts.
  5. If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Apr 01, 2010 | 1993 Volkswagen Golf

1 Answer

Timing belt


  1. THIS IS FOR GAS ENGINE 4 Cylinders A 2.0L SFI (found in 93% of 1996 Volkswagen Golf)
  2. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s).
  3. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  4. With the distributor cap removed, the rotor should be pointing toward the No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch on the crankshaft pulley should align with the dot on the intermediate shaft sprocket.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt.
  6. Slide the timing belt from the sprockets.

To install:
  1. Check the alignment of the timing marks. On 16 valve engines, the mark on the tooth should align with the mark on the rear belt cover.
  2. Install the new timing belt and tension the belt so it can be twisted 90 ° at the middle of it's longest section, between the camshaft and intermediate sprockets.
  3. Recheck the alignment of the timing marks and, if correct, turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck belt tension and timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45 Nm).
  4. Install the belt cover and accessory drive belts.
  5. If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Jan 15, 2010 | 1996 Volkswagen Golf

1 Answer

I need a new timming belt on a 01 kia sephia how do i change it


Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.

fd440e5.jpg
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.

1d207cf.jpg

4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.


077a275.jpg

6. Remove water pump pulley.

2bc0452.jpg


7. Remove crankshaft pulley and timing belt guide plate.



8619b52.jpg


8. Remove upper and lower timing belt covers.


c250533.jpg


9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.


213d3a1.jpg




10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.



a3188ba.jpg



11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.


12101a7.jpg

14. Remove timing belt.



Regards,
Jeep Brainy

Sep 20, 2009 | 2001 Kia Sephia

2 Answers

The Timing belt


Recommended by kia is 100,000 km.

Timing Belt: Service and Repair
TIMING BELT
COMPONENT
REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from Power Steering (P/S) and/or Air Conditioning (A/C) compressor
drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley and timing belt guide plate.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned
with mark on cylinder head cover.
NOTE: Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt.
NOTE: Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.
INSPECTION
NOTE: Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 inch (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
NOTE: Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.
INSTALLATION
1. Install tensioner pulley.
NOTE: Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned
with mark on cylinder head cover.
NOTE: If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that
order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
NOTE: Do not add additional tension.

8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque: 28 - 38 ft. lbs. (38 - 51 Nm, 3.9 - 5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on cylinder head cover.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from
tensioner installation.
Deflection pressure: 22 lb. (98 N, 10 kg)
Deflection: 0.39 - 0.50 inch (11 - 13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque: 5.8 - 8.0 ft. lbs. (7.9 - 10.7 Nm, 0.8 - 1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque: 9.0 - 12.6 ft. lbs. (12.3 - 17.2 Nm, 1.3 - 1.8 kg-m)
15. Install water pump pulley.
Tightening torque: 9.0 - 12.6 ft. lbs. (12.3 - 17.2 Nm, 1.3 - 1.8 kg-m)
16. install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

Sep 17, 2009 | 2003 Kia Rio

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

Timing Belt


I have used the Haynes Repair Manual for the Mercury Villager to change the timing belt on my 1993 Villager, twice. I just finished last night with the latest change. I found the Haynes manual to be very useful. This is just an overview:
1. Jack up the the van and support it on jack stands. Remove the front passenger side wheel and 2 plastic splash sheilds.
2. Remove the two radiator hoses on the passenger side of the engine.
3. Remove the pulley from the water pump (4x 10mm bolts)
4. Remove the tensioner pulley, including the bracket, for the A/C compressor. (3x 12 mm bolts)
This one can be difficult because it requires a torx head to loosen the pulley and it's a very tight fit to get a torx in there. I ended up taking the torx head out of the socket then turning it with a 10mm wrench.
5. Remove all 3 drive belts.
6. Remove the crankshaft pulley. (1-1/16" bolt) You will need a good strap wrench to keep the pulley from turning or an impact to remove this bolt. You may be able to remove the pulley just by bumping it with a mallet, but you may need a gear puller.
7. Remove the timing belt cover, it has an upper and lower half and is held in place by several 8mm screws.
8. You will find that the timing belt pulleys on the both cam shafts and the crank shaft have a white paint mark on one tooth. Make sure the marks on the two cam shaft pulleys are in line with a "bump" mark on the back plate of the belt cover. The bump mark for the front cam is located at about the 2 o'clock position and the one for the rear cam is at about the 10 o'clock position. You will need a mirror and flashlight to see this one.
The crankshaft pulley mark lines up with a notch in the oil pan (I think it's the oil pan where the notch is, but you will see it at near the 6 o'clock postion.
9. My new timing belt was a DAYCO and it came with a good instruction sheet. The new belt has an arrow that should point AWAY from the engine. There are also 3 lines on the new belt that will line up with the lines on the timing belt pulleys.
10. The belt tension should be adjusted so that you get about 0.5" - 0.6" of deflection at the center between the two cam shafts.
Note: I recommend replacing both the tensioning pulley and water pump while you are in there.
A water pump is about $32 and the tensioning pulley is about $35 but it's money well spent.
I did NOT replace the tensioner pulley the last time I changed the timing belt, and that is what failed this time. I could have saved myself a lot of work if I had replaced the pulley the first time.

Hope this helps. I'd still buy the HAYNES manual.

Dec 15, 2008 | 2001 Mercury Villager

Not finding what you are looking for?
2001 Volkswagen Golf Logo

2,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...