Question about Ford Ranger

Open Question

View diagram for windshield wipers 96 ford ranger

Posted by on

  • benjamwh7 Sep 10, 2009

    where is the diagram so i can view it?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
baccardo
  • 150 Answers

SOURCE: Windshield wipers turn on when ever they feel like it, but still work normally if i need them.

check for a short in the multifunction switch

Posted on Apr 18, 2009

Ad
  • 3 Answers

SOURCE: Ford Ranger windshield wiper problem

Sounds like you might have a ground problem.
In the morning its damp and might loose connection.Try an alligator clip
to a good ground.Test it in the a.m.

Posted on Aug 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: I cant figure out how to change my windshield

How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:

  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Posted on Sep 16, 2009

jbass706
  • 167 Answers

SOURCE: how to fix obd2 code 1443 on 96 ford ranger emisson test failed

It is usually carbon pieces from the evap carbon canister clogging the purge solenoid and purge flow sensor. There should still be a one piece purge solenoid and purge sensor with hose assembly available. You will also need to replace the carbon storage canister.
After replacement disconnect the negative battery cable, hold your foot on the brake pedal for 30 seconds, then reconnect the battery.

Posted on Oct 25, 2009

  • 246 Answers

SOURCE: ford f150 windshield wiper bushing diagram

sounds like a loose nut. there are nuts that hold the wiper arms on, they may be under a cover but theyre at the base of the wiper arm. also there's a nut that holds the wiper linkage onto the wiper motor. if you can move the wipers independently, it's the nuts connecting the wiper arms.if you move one arm and the other moves with it, it's the nut holding the linkage to the motor.

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reattach wiper arms on my ranger


Video says almost all (ranger/explorer similar)...
How To Install Replace Windshield Wiper Blades and Arms Ford Explorer...


https://www.youtube.com/watch?v=c-tR49oL1FQ

May 11, 2015 | 1999 Ford Ranger SuperCab

1 Answer

Windshield wipers not working correctly on ford f150


Not sure what year your truck is but on later models there is a wiper module. On my '96 I had to replace the wiper module that was located under dash on passenger side

Oct 27, 2017 | 1988 Ford F 150

1 Answer

My 1995 Ford Ranger's windshield wipers don't work


That involves airbag removal & a lot of delicate work. Let someone experienced handle it.

Jul 15, 2017 | Ford Ranger Cars & Trucks

1 Answer

What fuse works the windshield wipers for 1998 mustang?


go to this free Ford website to view or download the users manual for this vehicle. the fuse block diagrams are located in the roadside emergency section.
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

May 15, 2010 | 1998 Ford Mustang

1 Answer

Windshield wipers only work on high on 98 ford ranger


Try replacing relay for wiper with another same relay from fuse block from another working accessory.Had same issue on friends Ford Ranger. Moved relays and cleaned harness connection at fuse block. Works fine.

Mar 14, 2010 | 1998 Ford Ranger SuperCab

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Removing/replacing wiper motor in '93 Ford Ranger


You don't have to put the wipers in an upright position You can take the arms completely off. It's very easy to do, when you are looking at the base of the wiper arm, on the side closest to the windshield, at the base, there is a spring-loaded tab. Lift the arm on its hinge to where the arm is now pointing away from the windshield, pull the tab and the wiper arm will slide right off. Now you can access the linkage joints easily. Hope that helps!

Nov 09, 2009 | 1993 Ford Ranger SuperCab

1 Answer

Windshield wiper fuse is out, no fuse diagram


you could try online or just pull one at a time you'll know which one it is when you find it

Sep 20, 2009 | 2005 Ford Ranger

1 Answer

Ford Ranger windshield wiper problem


Sounds like you might have a ground problem.
In the morning its damp and might loose connection.Try an alligator clip
to a good ground.Test it in the a.m.

Aug 06, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...