Question about 1988 Ford F 150

Open Question

Removing carburetor from 1988 ford f 150 - 1988 Ford F 150

Posted by on

  • yadayada
    yadayada May 11, 2010

    what engine

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1988 E-150 4.9L Van (Ford)

Alright, it can be quite a Job. Starting of course by removing the door cover you can almost immeditaly take out the old one, its getting the new one in thats the triky part. you have to bend the fusing rods over about a half an inch because any new ones they make now are bigger than the stock ones. then you have to re route the converter ions to the back-up power control to get optimum power for your window. then you have to make sure the new motor is in place becuase it can fall out easily, put a screw right threw it and into the door. that should do it!

Posted on Jul 08, 2008

  • 308 Answers

SOURCE: 1988 ford f-150 xlt - starting problem

can't remember the exact name or the problem, it is a part of the igintion system, like the cheapest part. It is the most common on those fords

Posted on Apr 10, 2010

  • 2309 Answers

SOURCE: how do you remove the

seems to me that some of these were permanent connections, i may be wrong

Posted on Oct 24, 2010

  • 508 Answers

SOURCE: HOW DO YOU REMOVE THE

Two possible options here depending on which transmission you have. You will need to remocve the carpet or rubber mat on the floorboard. Under that you will have a stamped steel piece that removes from the floor. Then you will either have to drive a roll pin out of the tower holding the stick or it could be a push and twist on the collar. Worst case would be to remove the bolts that secure the shift tower to the tranny. If that is the case- make sure you put the tranny into neutral before removing the top cover. It will make it easier for you to install again. The stick and the shift forks will just come out as an assembly. Be sure to cover the tranny after you remove the top plate to prevent dirt from entering the tranny.

Posted on May 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 ford f-150, 5.0 eng. truck is idling way too fast after it's warmed up. Why???


check emissions controls for leaks.. may have a vacuum leak in the hoses somewhere.

Feb 10, 2013 | 1988 Ford F 150

1 Answer

I have a f150 88 fuel In.and i wand to element the In. and make it a carburetor Wat can of intake i need? and from wat year? Thanks


That depends on your engine size and setup, however, edlebrock will have a aftermarket intake that will direct fit to your truck.

Jun 09, 2011 | 1988 Ford F 150

1 Answer

How do you disable timing advance on 1984 Ford F-150?


Remove the vacuum line running from your carburetor to the distributor.. Plug the nipple on the carburetor so you don't lose vacuum.

Nov 03, 2010 | 1984 Ford F 150

1 Answer

How do you remove the hydraulic line from the clutch master cylinder on a 1988 Ford f-150?


seems to me that some of these were permanent connections, i may be wrong

Oct 24, 2010 | 1988 Ford F 150

1 Answer

How to rremove a timing belt/chain on a 1988 ford f-150. 4.9l engine


remove fan and pulley remove harmonic balancer remove water pump take timing chain cover off should be either 7/16 or 1/2 socket remove top timing chain not gear yet line up dots bottom gear dot at 12 oclock top gear at 6 oclock then remove gears and replace

Sep 18, 2010 | 1988 Ford F 150

1 Answer

I need to replace my starter on my 1993 Ford F-150


Remove the drive belt remove the screws on the starter,replace the starter,re insert the belt and adjust screw to proper tension...easy

Jan 20, 2010 | 1988 Ford F 150

1 Answer

1988 Ford F-150 ignition lock cylinder replacement when you lose the keys, anyone know a simple way to replace it when you don't have the keys?


No real simple way. Steering wheel removal is required and drilling out the retainer pin .
Taking out the cylinder from the outside is possible but damage to the steering column is a risk and lots of patience with a die grinder is needed.

Nov 05, 2009 | 1988 Ford F 150

1 Answer

How to replace the wiper motor on a 1988 Ford F-150


1-remove wiper arms 2-remove cowl 3-undo linkage drive from wiper motor 4-remove elect.connection from wiper motor,remove mounting bolts,remove wiper motor.

Apr 17, 2009 | 1988 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...