Question about 1999 Ford Crown Victoria

2 Answers

03 Crown Vic wiper works on high only nothing on any other position stops were they are when taken off high

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem switch seems fine and I can hear a click under the center dash when I operate the switch I had several replies about the same problem that was fixed by replacing the wiper motor , They run about $ 65 dollars but It will be alot cheaper than having a Mech replace the switch

Posted on Oct 02, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 388 Answers

The wiper switch is most likely at fault. Have a mechanic take a look at the switch.

Posted on Sep 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I look for relay fuse that work on wipe motor, 1999 ford crown vic


I suggest check position 2, 30A for Wiper Control Module, Windshield Wiper Motor...

10_19_2011_3_21_07_pm.jpg

Keep in mind that this and other important information could find in Ford Crown Victoria owners manual.

Hope this helps; just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Have a nice day and thanks for using FixYa.

Jose.

Oct 17, 2011 | 1999 Ford Crown Victoria

1 Answer

Crown Vic: Window shield wipers turn on by themselves.


DISCONNECT WIPER SWITCH IF WIPERS STOP REPLACE SWITCH.IF WIPERS DONT STOP. YOU HAVE A DEFECTIVE LIMIT SWITCH IN MOTOR.

May 28, 2010 | 2003 Ford Crown Victoria

2 Answers

Wipers only work on high speed. washer pump work too. I have no low speed or delay for wipers. Is this a switch problem or is there a relay modual under the hood that could be bad


Hello, this is a very common problem for Chevrolet. Your wiper motor control module is bad. It's mounted directly onto the wiper motor. On some models you can replace the "pulse board" inside the control module. If not you need to replace the entire wiper motor control module. It depends on your level of skill and parts availability.

Feb 02, 2010 | 1999 Chevrolet Express

3 Answers

Wipers stay on


Looks like the wiper motor uses G102 as the grounding point, should be close to the fuse box in the engine compartment. If you lift it and it stops then you may have a bad switch in the motor.

Oct 09, 2009 | 2003 Ford Crown Victoria

1 Answer

Where is the wiper control module on a 2004 crown vic


i believe it is part of the wiper motor which should be located in the driver's side rear corner of the engine bay, on the firewall. Many 03 and up Fords use a "Smart motor" for the wipers which has the motor and a module in one piece.

here is a diagram

Oct 07, 2009 | 2004 Ford Crown Victoria

2 Answers

Wiper


Odds are your wiper control is faulty and you may need to replace it which involves removing 3 screws that secure the assembly to the steering column.

Sep 09, 2009 | Cars & Trucks

2 Answers

Wiper motor replacement for a 99 crown vic


I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

May 06, 2009 | 1999 Ford Crown Victoria

1 Answer

Fuse box diagram


Locations In Case this Picture Doen not SHOW UP FOR YA --
WIPER Fuse ok Lookin at the box with the Round Circle In TOP RIGHT Corner Wiper is Number 2 Bottom from That Circle would be 2nd one from right Suppose to Be a 30 amp fuse Hopin this Helps Ya If so Please RATE Me AS High as You feel I Dererve Thank You and Good Luck with the CROWN VIC
Notes 78246312

Jan 11, 2009 | 1999 Ford Crown Victoria

1 Answer

Wipers


It's probably going to be the switch arm itself.

The part is a bit pricey, but it does come with the wiring diagram to place the new one in there.

The switch is the whole thing, turn signal, wipers, etc, and the arm.

Dec 20, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...