Question about 2001 Mercedes-Benz C-Class

Open Question

C Class 2002 speed pulse wire? :S

Anyone have the locatiion of the speed pulse wire in a Mercedes C CLASS

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 784 Answers

SOURCE: alternator repair 88 mercedes e class

There are 2 types of Alt for your car .The lower Amp has a Plug in the high Amp has a screw in for electrical connection.
There are 2 bolts to hold the Alt in the engine. Need to locate them first and losen them up.
Losening the tension is a bit tricky. There is 1 large bolt I don't remember size maybe 17mm between the compressor and the power steering pump.
Need to loose it first before attemping the top bold near the Power steering reservoir, other wise you will strip the thread and this is a lot of work to replace.
After you done all of that in order, you can completely take off the 2 bolt at the Alt. Pull the top bolt first so the ALt can be Pivoted to the bottom one, then one hand to hold the Alt while the other to pull off the bottom bolt.
Put in the new Alt in reverve order.
Good luck

Posted on Jul 04, 2009

  • 22246 Answers

SOURCE: 2005 mercedes c class will not start

Dealer only ,encrypted software ,start playing with it and?????? if anything goes wrong then factory immobilisor cuts in and it has to be connected to the internet via factory and it will not be released to start unless the bar code on the spare part box has been read by the operator with the bar code reader thats on the computer .This part is then recognised as the relevant fault code from the diagnostic check and with a genuine part for that fault code the computer releases the factory immobilisor.SO MUCH FOR THE AMERICAN FREEDOM OF INFORMATION ACT

Posted on Nov 13, 2009

  • 165 Answers

SOURCE: mercedes benz 2002 c-class owners manual

Posted on Apr 18, 2010

  • 279 Answers

SOURCE: the blower works only on one speed.on 2 3 4 and 5

Sounds like the resistor block that gives you the various fan speeds has had it. This is a replacement only part and in most cars can be found close to the blower fan up into the air box.Consult your dealer for exact location and cost.It's not a hard job to do,just a biy hard on the back.Good Luck

Posted on Oct 24, 2010

  • 3400 Answers

SOURCE: Need code for AL2299W0716245, MERCEDES Problem

If you're after radio code, you need to contact a Benz dealer and provide your VIN#. Dealer is only source for anti theft radio codes.

Posted on Mar 01, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1995 c280 Mercedes-Benz can not run beyond 120 speedometer, once I try to go beyond 120 speedometer it will start cutting fire pls can anyone help me

Cars produced in Germany are electronically speed limited to about 150 mph. This is embedded in the software. If there are no other problems with the engine, fuel or transmission it is possible the management system has been remapped and the speed limiter has been reset to 120 mph.

Sep 04, 2016 | 1995 Mercedes-Benz C-Class

2 Answers

Mercedesw202 c200 pms ecu system . car wont start

Hi I have a 1995 C200 Auto Sedan chs WDB 2020202F241703, I think I have a problem in the ECU. Only runs on two cylinders, I have changed the core pack on the 1 & 4 cylinders but the problem persists. The other problem is I don't know where the ECU (engine computer ?) is can anyone help ?

May 17, 2010 | 1995 Mercedes-Benz C-Class

1 Answer

I have a 1993 300E mercedes and my idle air/speed control valve needs to be clean or replaced. how do i remove and install this part?

Remove MAF disconnect wires unbolt/unscrew, disconnect linkage and remove and replace. Im sure the wires are degraded in it and the engine wiring harness as MB was forced to use by the US biodegradable insulation on its copper wires from 1993-1995 just like saab and subaru.

Apr 19, 2010 | 1993 Mercedes-Benz Mercedes Benz 300 Class

2 Answers

Mercedes Vito audible speed alarm - how do you turn it off?

follow the directions in your owners manule if you need a new 1 try looking at salvage yard

Jan 23, 2010 | 2002 Mercedes-Benz S-Class

1 Answer

Merrcedes-benz 200 wiring diagram

E class merc ing barrel wiring as some one changed it and the wires come out the plastic housing at rear 1994 car

Nov 29, 2009 | 1990 Mercedes-Benz E-Class

1 Answer

Mercedes 2001 trunk lock fastener wiring diagram

Go back to the dealer and make sure they gave you the right part. Dealerships will also give you a wiring diagram, if you ask nicely.

Sep 04, 2009 | 2001 Mercedes-Benz C-Class

1 Answer

ASD light is on in my mercedes 300E

First the sensor in the rear gearbox may be bad or corroded for sensing wheel speed. Also the engine wiring harness may be falling apart. From 1991-1995 the US made MB use biodegradable material on the wiring. When the insulation cracks you get shorts in the system. The same wires are in your EHA on the air inlet area. Check and replace as needed.

May 26, 2009 | 1994 Mercedes-Benz E-Class

Not finding what you are looking for?
2001 Mercedes-Benz C-Class Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

76846 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides