Question about 1988 Chevrolet Monte Carlo

1 Answer

Put in new seals and they are leaking

Put in new seals on my 1988 Monte and they are leaking

Posted by on

  • art41 Sep 10, 2009

    T-Tops

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Which seals were replaced?

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy Monte carlo output seal leaking do I need a new transmission


Possibly just a new seal but the ****** has to be dropped any other problems will be revealed then

Oct 15, 2012 | Cars & Trucks

2 Answers

My 88 monte carlo SS tries to cut off at stop signs/lights


sounds like a vacuum leak, whether it's carbureted or fuel injected a vacuum leak can cause a variety of problems. this could just be a loose or missing vacuum line or a bad brake booster, do you hear a vacuum leak sucking sound coming from under the dash? that's a good sign that the booster's bad.

Jan 09, 2011 | 1988 Chevrolet Monte Carlo

2 Answers

2003 monte carlo a/c works of and on,already put freon in twice and the security light omes on and also the traction active light comes on


Re the a/c. Get a can of red tek sealer. make sure the engine is cold or you won't get the connector on to the low side port to seal properly. Follow the insrtuctions that comes with the can. Just adding the refrigerant doesn't stop the leak

Sep 14, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

Transmission fluid leaking back, 1988 Ford Bronco


your output seal on the tranny or input seal on your transfer case is bad. you have to pull your transfer case to tell. this is a pretty straight forward job. block wheels. put transfer case in neutral. drop front and rear drive lines.diconnect transfer case shift linkage. there is a short commponent connecting the trans to the transfer case. the bolt on either end face each other. remove the bolts to the transmission. the transfer case is heavier than it looks, i suggest getting help. pull back on the transfer case until it will drop down. it will pull out a bit because of the trans output shaft. replace what will probibly turn out to be the tranny output shaft seal and reassemble in reverse order.

Nov 06, 2009 | 1988 Ford Bronco II

1 Answer

Wheel bearings on 1988 chevy S-10


remove grease cap,brake caliper, then remove nut holding rotor now remove rotor, remove grease seal now both bearings should be out ,if replacing races then punch them out and tap new ones in, repack new bearings with grease install rear one and install new grease seal, slide rotor on slide frt bearing on, install washer and nut, tight a little to nearest cotterpin hole,put cotterpin in and put caliper on, hope this helps,good luck.

Oct 27, 2009 | 1988 Chevrolet S-10

1 Answer

Transmission leak


Hi,

No clamp, it sounds like it is just a bad seal.
Just remove the drive shaft and pry out the old one and tap in a new one. very easy on those cars. juts make sure you put some tran fluid on the rubber part of the seal before installing the drive shaft or it can tear it.

Mar 31, 2009 | 1988 Mercury Grand Marquis

1 Answer

1988 Cadillac Power Steering Leak


BETWEEN THERESERVIOR AND PUMP ASSEMBLY THERE IS A O RING IT MAY BE MISSING OR CUT WHEN THIS PROBLEM IS CORRECTED (MAKE SURE PLASTIC RESIVOR(SP) IS NOT CRACKED) IF NO MORE LEAKS MAKE SURE IT IS FULL OF FLUID, RAISE FRONT WHEELS OFF GROUND KEY ON ENGINE OFF TURN STEERING WHEEL LOCK TO LOCK 50 TIMES. THIS FROM A CADILLAC SERVICE BULLETIN THIS WILL REMOVE AIR FROM THE SYSTEM

Oct 20, 2008 | 1988 Cadillac Sedan DeVille

Not finding what you are looking for?
1988 Chevrolet Monte Carlo Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...