Question about 1985 Mitsubishi Galant

1 Answer

Please help!!! what is the cilinder on the thratle body housing located on the intake has small screens on the sides for the gas and a small spray port on the bottom it has 2 wires coming from it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

That is your injector

Posted on Sep 10, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Where is thermostat located 4.3 liter chevy s10, 2003

The thermostat is located inside the steel thermostat housing, which is located on the front of the engine right in front of the throttle body housing and halfway between the alternator and a/c compressor. Remove the air intake assembly and remove the front bracket connected to the front two bolts of the throttle body. Then remove the two main bolts of the thermo housing. Lift up the thermo housing and you will see the thermostat sitting there.

Sep 30, 2015 | Cars & Trucks

1 Answer

2002 ford explorer will not start sometimes battery is ok turns over starter is ok it is cold now starts ok in morning drive for about 15 minutes stop car for 1 hour 15 minutes come out to start car does...

Possible fuel pump. Check the fuel pump pressure;or remove the air intake hose from the throttle body.spray some gas with a squirt bottle in thratle body. replace the intake hose and crank it; if it turns on, your pump is bad.

Mar 27, 2017 | 2002 Ford Explorer

1 Answer

I need a diagram for the thermostat on the 2000 pontiac grand am 3400

The thermostat is located in the thermostat housing which is located on the intake manifold under the throttle body. If you have small hands, you can remove the air intake tube from the throttle body and the exhaust crossover heat shield. Once there out of the way, you can remove one of the bolt and losses the other to slide the thermostat housing off to replace the thermostat.

If you can not get to the bolts, then your going to have to remove the throttle body and don't forget the order the new throttle body gasket also. Not that the coolant temperature sensor is on the intake manifold in front of the thermostat housing, so take caution not to damage it when removing the housing.

Thank you for using fixya and keep us posted.

Oct 02, 2010 | Pontiac Grand Am Cars & Trucks

1 Answer

What are the steps to replace the speed sensor? Do I access it from above or below.

Speed Sensor Removal
  • Use the Phillips screwdriver to loosen the screw in the intake boot clamp at the throttle body. Slide the intake boot off the throttle body. Pull the other end of the intake boot off the air filter housing.
  • Locate the Accord speed sensor at the top of the back side of the transmission, close to the firewall. It has two 10-mm bolts holding it in, and an electrical connector at the top. Unplug the electrical connector by squeezing the clip at the top and sliding it off the speed sensor.
  • Use the ratchet, extension and 10-mm socket to remove the two bolts located on the sides of the speed sensor.
  • Remove the speed sensor by pulling on it. You may have to twist it back and forth to work it free. If the drive link does not come out with the speed sensor, remove it from the transmission. The drive link is a very small part that links the speed sensor with the transmission.
  • Speed Sensor Installation
  • Insert the drive link into the new speed sensor. Carefully place the speed sensor onto the transmission, making sure that the drive link lines up in the shaft.
  • Install the two 10-mm bolts and tighten them until they are snug.
  • Slide the electrical connector back onto the speed sensor until it clicks into place.
  • Reinstall the intake boot by sliding it over the throttle body and air filter housing. Tighten the Phillips screw in the clamp at the throttle body.
  • Start the Accord and test drive it to verify that the speedometer is working properly.

  • Sep 25, 2010 | 1991 Honda Accord

    2 Answers

    I have a 2006 chevy aveo. i was told the throttle position sensor was out. i bought the sensor. i cannot find the location on the engine where it goes. is there a photo available which would show the...

    Easiest thing to do would be to follow the air intake tube to the throttle body.( big round rubber or plastic that goes from front area of car to engine and is usually held on with a clamp where it attaches to intake of throttle body) Right in that area, you will see your throttle linkage/cable etc, and where it pivots when gas pedal is pushed. Look opposite side of that housing and you should see the throttle position sensor.

    Jul 27, 2010 | Chevrolet Aveo Cars & Trucks

    3 Answers

    I'm trying to locate the IAT sensor plug . theres so many sensors in the same area that I cant determine which one it is .

    I'm sending you a illustration of the IAT Sensor location only 2.4L engine.
    Mitchell on demand does not have a illustration for the 3.4L engine but they say its at left side of engine compartment. I hope this will be of some help.d15406a.gif

    Oct 04, 2009 | 2000 Pontiac Grand Am GT

    1 Answer

    Where is IAT sensor located on 2004 f350 5.4L V8

    2004 Heritage & Lightning ( guess this is your config, with posted in 2003 section ).

    Looking at the engine, the air filter housing is the large round tube on the right hand side ( driver's side or left when reading descriptions )
    The IAT is in the pleated section of the intake ( factory intake ) to the left of the air filter, about where the power steering fluid reservoir is at ( it should be pointing towards the back of the truck ).
    Small black connector with a plastic wire loom on it.

    2004 Non heritage ( New Body Style ) :
    It is on the side of the large housing that holds the air filter ( on the stock intake, not a FIPK kit from K&N or the likes ).

    Looking at the engine, the air filter housing and tray are on the top ( 2 latches hold the air filter tray in ), on the right hand side just behind the top of the T shape ( looking down on it ).

    The connector should be black with a trace of red on it.

    Oct 03, 2009 | 2003 Ford F150 Regular Cab

    1 Answer

    Need to know were the throttle sensor unit is located

    ok, this is a fairly easy thing to find. ill try to explain it in a simple way...start at your air filter under the hood. follow that long intake tube that runs to your engine from the airbox. it will be attatched to whats called the throttle body. its a small housing that is bolted on to the engines intake manifold. now on this housing, there will be a sensor mounted on the side with probably 3 or 4 wires attatched to it with a plug. this is your throttle position sensor.

    Aug 31, 2009 | 1999 Volvo C70

    1 Answer

    Can't find the thermostat?!?!

    It's located in the intake manifold under the throttle body, Follow the radiator hose from the drivers side to the engine. The hose is then connected to the thermostat housing which goes under the throttle body and behind the exhaust pipe. 
    if you have small hands and the right tools you can get it out with out disconnecting the exhaust pipe or throttle body. 
    Good luck and i feel the pain. Keep me posted.

    May 29, 2009 | 1993 Oldsmobile Cutlass Ciera

    2 Answers

    Where is the thermostat on the 2002 suzuki aeiro

    follow the upper radiator hose to the housing on the intake manifold. it is held down with 2 bolts. on some small vehicles it will be located under throttle body hose from the air filter.please rate this.

    Sep 20, 2008 | 2002 Suzuki Aerio

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    29 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts


    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8201 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides