Question about 2000 Suzuki Grand Vitara

1 Answer

How do I remove and replace the front axle?

How do I remove and replace the front axle for a 2000 suzuki grand vitara?

Posted by on

  • Anonymous Mar 29, 2014

    how to replace axles on 2000 Suzuki esteem front both sides

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

You first need to remove the big nut that is holding the wheel on the side that you are trying to replace first you must buy the right sized socket thet will fit the nut the while the vehicle is still on the ground take the hub cap off and the cater pin out and then put the socket on the nut using a halt inch tourge ratchet loosen and remove the nut then jack your vehicle up and remove the wheel and the bolts that are holdung the hub and then with a pickle fork that is the tool used for removing tie rod ends that is connected to your stirring and then after that remove your axle and then reverse the procces to put ti back together.

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Vitara. axle out of front differential and leaking, passenger side . ??


CHANGE AXLE OUT .ABOUT 70.00 DOLLAR PART. REPLACE SEAL AT THE SAME TIME

Feb 27, 2012 | 2001 Suzuki Grand Vitara

2 Answers

2000 suzuki grand vitara 4 wheel drive will not engage


2000 Suzuki Grand Vitara rear Wheel Drive working but 4wheel
is not working, dash 4wheel sign light not working

Jan 12, 2011 | 2000 Suzuki Grand Vitara

2 Answers

Where is the fuel filter located in a 2006 Suzuki Grand Vitara 2l?


in front of the fuel tank. above the rear axle towards the passenger side.

Nov 19, 2010 | 2006 Suzuki Grand Vitara

1 Answer

How do i change the rear axle seal on a 1999 grand vitara


how do i remove the axle seals on a 1999 suzuki grand vitara

Mar 02, 2010 | 1999 Suzuki Grand Vitara

2 Answers

1999 Suzuki Grand Vitara Vibrate/shake at 55-70 mph


Lift the back of your car.With a stable rest and with the two hind wheels hanging, run your car up to the speed where you experienced vibration. have someone take care of the throttle and shifting while you observe the transmission shaft. You may have an imbalanced shaft.

May 12, 2009 | 1999 Suzuki Grand Vitara

1 Answer

Where is the starter for a 2000 suzuki grand vitara located


starters are normally located at the rear of the motor usually hard to get too or see. should be on your bell housing in other words just in front of the gearbox/clutch

Dec 23, 2008 | 2000 Suzuki Vitara

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
2000 Suzuki Grand Vitara Logo

723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...