Question about 2001 Kia Rio

2 Answers

Tightening procedure on front axle shaft 2001 kia rio

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Center NUT Is 110 Ft Lbs

Posted on Sep 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

180 ft lbs.

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of vehicle speed sensor n 2006 kia rio


Its mounted to the rear axle housing and both front half shafts.

Jan 11, 2017 | 2006 Kia Rio

1 Answer

How do i hold the motor still to take off the bottom crank shaft pulley on a 2001 kia rio


You need a air impact gun like tire shops use..
You can also remove the starter motor and jam the flywheel teeth with flat ended large bar.

Sep 12, 2012 | 2001 Kia Rio

1 Answer

How to remove a front wheel bearing on a 2001 kia rio


Does 2001 kia rio need to have a spacer for the driver side wheel bearings

Aug 25, 2012 | 2001 Kia Rio

1 Answer

Which way do you unscrew axle nut on 2001 kia rio


Counterclockwise -to the left

Nothing odd about that

Jun 29, 2011 | 2001 Kia Rio

1 Answer

My 2001 kia rio automatic transmission appears to run as if is in neutral when placed into every gear. The linkage has been observed and appears to be connected and in working order and the transmission...


Check if ur axle in front is moving, if it is moving u got a LOOSE NUT on ur front wheel axle, some front wheel drives have tendency to loosen the nuts holding the axle to turn the wheel.It may also have a damage AXLE, let the mechanic check that! In ur transmission, modern automatic transmission have SLOENOiDS that acts to shift the FLUiD from one gear to another and its not FUNCTiONING. Better bring it to ur nearest dealer to check on that SOLENOiDS Most of the Transmissions today are electronically controlled!

Nov 17, 2010 | 2001 Kia Rio

2 Answers

I have a 2001 kia rio, we have replaced front wheel bearing a combined total of 12 times and it only has 81000 miles on it. one are the other goes out about every 10000 miles.can we replace the older axle...


well not sure what you mean by one piece assm. becuase all front wheel drive cars require one shaft and two c/v joints on either end.

but i think i have a hunch of the problem and them most common cause for failure after a replacement is over tighting of the axle nut. what happens is it crush's the bearing and cut's it's life.

Apr 20, 2010 | 2001 Kia Rio

1 Answer

What is the toque for the cam shaft bolts on a 05 kia rio 1.6L


This is for 1.5L & 1.6L (VIN 5) Engines

Tighten the bolts, to 8–11 ft. lbs. (11–15 Nm).


This is for 1.6L (VIN 3) & 2.0L Engines

Install the camshaft and bearing caps. Tighten the bearing cap bolts to 10.5 ft. lbs. (14 Nm).

Jan 19, 2010 | 2005 Kia Rio

1 Answer

Where is the speed sensor on a 2001 kia sportage located?


The speed sensors are a single pole, variable reluctance sensor, mounted to the rear axle housing and both front half shafts.

A toothed tone ring is press fit to the differential carrier next to the drive gear and provides the signal for the rear sensor.

The front tone rings are press fit to the half shaft assemblies

Nov 15, 2009 | 2001 Kia Sportage

1 Answer

I need to remove the outend of the drive axle and am having troubles getting the axle out of the hub. Every other place has indicated that it just slides nicely out with little or no force. However on this...


Put the axle nut back on backwards (flat side out, so flat is even with the axle end...give it a sharp blow with a decent sized hammer and it will break loose.

Apr 01, 2009 | 2001 Kia Rio

Not finding what you are looking for?
2001 Kia Rio Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...