Question about 2000 Ford Windstar

1 Answer

I HAVE A 2000 FORD WINDSTAR THAT WILL ONLY GO INTO REVERSE. IT WONT GO INTO DRIVE. COULD IT BE THE PUMP?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 246 Answers

No if the pump was bad it wouldn move at all,the problem is internal,have it checked

Posted on Sep 10, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 743 Answers

SOURCE: My Ford Windstar 1999 doesn't drive forward or

Has the transmission ever had any services done? Its possible it has just gone out. There are clutches and bands inside and without proper service they will go out.

Posted on Sep 02, 2011

Testimonial: "Thanks, I will be taking it in to service the trany (rebuild)."

  • 166 Answers

SOURCE: i have a 1996 ford winstar that wont auto shift

have the trans rebuilt

Posted on Jun 10, 2009

jbass706
  • 167 Answers

SOURCE: 2000 ford windstar transmission jumps when i put

If the mounts are okay and you are getting a hard slam it could be the TFT (Transmission Fluid Temp sensor in the trans pan) or the Pressure control solenoid in the valve/control body.

Posted on Oct 24, 2009

  • 68 Answers

SOURCE: Driving a 2003 Ford windstar. Went to pass and

Very common on this make and model trans, pump drive splines inside torque converter strip out and pump is not turning, Most times there is no damage to pump shaft. Remove trans and remove torque converter, inspect the splines at the very bottom of the hub hole. If stripped out inspected pump shaft splines which are the smaller center splines coming out of trans, if ok replace torque converter and re-install trans, change out fluid, clean any metal from magnet and replace filter, fill with fluid and verify proper operation.

Posted on Mar 01, 2010

  • 5 Answers

SOURCE: need instructions on changing fuel pump in a 2000 ford windstar

i fixed my windstar fuel pump problem.. fuse number 5 was blown.. replaced the fuse and all is better.. however i do hear an electrical spark when the fuel pump disengages .. (turning the key to the acc position)

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 ford windstar will not move when put in drive or reverse


run the fault codes and look for a torque converter solenoid/servo fault. Check for a TCM problem.

Nov 28, 2014 | 2000 Ford Windstar

1 Answer

Cranks but wont start


Someone will need to check the circuit at the pump to see if it is getting power from the relay. If it is the pump should be running when you first turn the key on.
You can also check for power at the pump relay.

Dec 13, 2012 | 2000 Ford Windstar

1 Answer

My 2000 ford windstar was working fine, then I stopped to put gas and when I tried to switch from park to drive it did not go in gear. no reverse, no drive, what would it be??


Hi hope I can help.
This is a very common way that a torque converter fails.
The transmission will need to be removed and a new torque converter installed.
Hope this helps
leave feed back
thank you urnuts73@fixYa

Mar 05, 2011 | 2000 Ford Windstar

1 Answer

Replacing belt on 2000 ford wingstar(diagram) 3.8litre engine


6a0c58e.gif


Item Part Number Description 1 8620 Drive belt 2 3D673 Power steering pump pulley 3 8A528 Water pump pulley 4 10300 Generator pulley 5 6C348 Idler pulley 6 2E884 A/C clutch pulley 7 6B321 Crankshaft vibration damper pulley 8 6B209 Drive belt tensioner

Aug 12, 2010 | 2000 Ford Windstar

1 Answer

Driving a 2003 Ford windstar. Went to pass and


Very common on this make and model trans, pump drive splines inside torque converter strip out and pump is not turning, Most times there is no damage to pump shaft. Remove trans and remove torque converter, inspect the splines at the very bottom of the hub hole. If stripped out inspected pump shaft splines which are the smaller center splines coming out of trans, if ok replace torque converter and re-install trans, change out fluid, clean any metal from magnet and replace filter, fill with fluid and verify proper operation.

Mar 01, 2010 | 2003 Ford Windstar

1 Answer

Lower radiator hose connecting tube to water pump. how do i remove and replace old metal tube 2000 ford windstar


remove the radiator hose remove the two bolts that hold the tube on and buy new tube and replace is in reverse order.

Jun 17, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...