Question about 2006 Lexus Rx 330

3 Answers

Passenger & rear power windows not working

Passenger and rear power windows do not work from driver's control panel, but DO work from each individual control. Also, driver's window works. 2006 RX330 only 26,000 miles.

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lexus Master
  • 1,564 Answers

First to keep with the basics, make sure you haven't inadvertantly hit the safety lockout button on your drivers side control panel. Then pop out or unscrew the switch from it's holder and check with a test light if the power is being ditributed to the other windows, if not you'll need a new door control modual and you'll have to take it to the dealer so they can code it and activate it according to your keyless entry system.This is probably covered under waranty and or recall. Thank you, Dana

Posted on Sep 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 229 Answers

Had the same problem, its a loose connector. pop the control bezel off and heck connections...I was fortunate I gave it a smack and it is still working.

Posted on Apr 21, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

Remove the control panel. Clean the tips of the wires, add some di electric grease to wires then try the control.

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

Buick 2002 LaSabre Custom all windows do not go up and down, door lock/unlock switch drivers side does not work(passenger & rear doors lock/unlock door switches work, trunk release button does n


coulb be the control switch on your panel you can take the door panel off and check for loose connections and try to test for continuity. if you dont know how take it to a shop and have them diagnose the electrical. im quite sure it the switch that burnt out

Oct 24, 2012 | 2002 Buick LeSabre

1 Answer

1995 Ford Taurus windows and locks not working


The windows and power locks are controlled through a central computer module called the Generic electronic module, you must have this module scanned by the dealer (or a well equipped shop with a Ford compatible scanner) to see what is wrong with the system.

May 23, 2012 | 1995 Ford Taurus

1 Answer

My passenger side,and rear power windows dont work and my lights dim when i try and let the passenger side window down the rear windows cause the car to do nothing. when i first bought the car the rear...


The motor on the passenger side is shorted and is now tripping the circuit breaker. Odds are, the back window motor is also bad. You have to take the panel off to check the motor. You can power it directly to verify it has failed.

Jul 22, 2017 | 1985 Pontiac Parisienne

1 Answer

Driver's side window will not work. Door locks work.


My mechanic took out the panel on the driver side control because my right rear passenger window would not work after disconnecting the battery (but the control on the passenger rear door works) and when he put it back, it worked..it's possible it's just a loose wiring connection. My car is a 2006 Lexus RX330 with 58K miles on it.

Aug 02, 2010 | 2001 Lexus RX 300

2 Answers

MBZ 1984 300D Driver side front window & passenger rear


Nope 1 fuse controls all the windows. Either its the switch or the window regulators themselves or due to the age the wiring.

May 03, 2010 | 1984 Mercedes-Benz Mercedes Benz 300 Class

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

1999 cadillac seville sts driver side master control pannel dead


The same circuit breaker feeds the driver door as well as the passengers doors . The wires inside the rubber boot from the body to the door are probably broke ,power or ground wire .Or the door module is bad . Are your familiar with electronic control modules ? The door functions ,windows , lock's , memory etc... are controlled by DDM - driver door module .
Door Control System Operation
This vehicle has five modules capable of performing door system control functions. Vehicle door system components (windows, locks, mirrors, etc.) are controlled directly by these modules. There is a door module located inside of each vehicle door:
• Driver Door Module
• Passenger Door Module
• LH Rear Door Module (LRDM)
• RH Rear Door Module (RRDM)
• LH Front Power Window Switch
Simple Bus Interface (SBI)
Each Door Module communicates with the other Door Modules on the SBI. The driver door module is the only Door Module that is capable of communicating over the Class 2 Data Line as well as the SBI.
Driver Door Module
The driver door module directly controls the LH Front door lock actuator, power window motor and the outside rear view mirror. The driver door module sends and receives messages received from the LH Front Power Window Switch to the passenger door module, LRDM and RRDM modules over the Simple Bus Interface (SBI) line. Also, the driver door module sends and receives message from other vehicle system modules via the Class 2 Data Line.
Pulling the door panel off an checking B+ voltage and ground for the module would be good for you to do , since you probably don't have a $6,000 factory Tech 2 scan tool to see if the DDM is communicating .
The driver door module has two main power feeds (high and low current), and two main grounds. The low power feed (battery 1) is used to provide power for the driver door module's logic and internal driver operation. The high power feed (battery 2) is used to provide power for systems that draw higher amounts of current (motors, lights, etc.). Operating current at the driver door module's battery should not exceed 3.0 amperes at battery 1, and 7.5 amperes (for 2 seconds) at battery 2 while the driver door module is awake, and 2.5 milliamps when the driver door module is asleep. For most driver door module functions, the driver door module will operate properly with a system voltage of 9.0-16.0 volts. If system voltages exceed 16.0 volts the driver door module will provide protection by disabling certain functions that may damage due to higher than normal system voltages.

What kind of manual do you have ? The info above is from a factory repair manual .
The fuse's ,circuit breaker for the door module are located in the rear fuse box , not under hood . PWR WDO circuit breaker 30 amp. , DRVMDL fuse 10 amp. The rear fuse box is located under the back seat . Watch this video ,different type vehicle but probably the same problem .
Dodge Grand Caravan No Power Window No Power Locks CAN Trouble

Jul 23, 2017 | 1999 Cadillac Seville

1 Answer

2003 F250 Power Windows won't work


check fuses 35 & 41 (10 amp, red).
it also shows an accesory delay relay in the fuse panel.
And fuse 601? 30 amp.

make sure you don't have lock-out on driver switch panel activated.

Power Window System
Features and Operation
NOTE: The accessory delay feature will allow power window operation up to 10 minutes after the ignition is off or until a door is opened.
If equipped with power windows, the window control switch (14529):
  • will operate the power windows only when the ignition switch is in the RUN or ACC position.
  • is located on each front door trim panel, and Crew Cab and Excursion rear door trim panel.
  • may be used to raise or lower the driver side, passenger side and rear windows from the LF control on the driver side, or the passenger window from the passenger switch.
  • includes a one-touch down (OTD) feature for the driver door window.
  • can partially lower the driver side window when the LF window control switch is depressed half way (first detent).
  • will completely lower the driver side window when the LF window control switch is fully depressed and then released (second detent).
Power Window System — Modes of Operation
There are two modes of operation for the power window system.
Manual Mode
When the LH window control switch is pressed to the first down position, the window will move down until one of the following conditions are met:
  • The LH window control switch is no longer in the first down position.
  • The LH window control switch is pushed to the OTD position, causing the windows to enter auto mode.
Auto Mode
Auto mode provides the OTD feature. The OTD feature is activated when the LH window control switch, for the LH window, is pressed to the second down position.
Auto mode will be terminated when any of the following conditions are met:
  • The LH window control switch is pushed to the UP position.
  • The LH window control switch is released (OFF position) and then moved to the DOWN position (first detent) or OTD position (second detent).
  • Note: Delayed accessory feature must be active.
The OTD feature is controlled by the window control switch.

---------------------------------------------------------
Condition Possible Sources Action
  • All power windows are inoperative
  • Fuse(s).
  • Circuitry.
  • LF window control switch.
  • Accessory delay relay.

May 23, 2009 | 2003 Ford F250 Super Duty Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

872 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...