Question about 2004 GMC Envoy

1 Answer

I changed the bulbs and checked the fuses still can't get the lights to work.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Are you talking all lights don't work?

Posted on Sep 10, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76848 Answers

SOURCE: Need fuse schematic

if the fuse was blown the stop lights on both sides would be inop, also if the stop light circuit were dead u would be unable to get the trans out of park, use a 12 volt test light and test the brake light switch at the top of the brake pedal, u can buy a test light from Autozone, kragen and others for about $5 US. If the system has power cjheck the bulb socket it may be defective, use the 12 volt test light while someone pushes the brake pedal. let me know what u find and i will give u further assistance as ness.

Posted on Jan 13, 2009

  • 1779 Answers

SOURCE: license's plate light stopped working even with new bulb.

It wouldn't be a fuse if that's the only light that's not working, I believe all of the parking lights are on the same fuse. It's most likely a bad ground or corrosion inside the socket where the bulb makes the electrical connection. So check the socket to make sure it has no corrosion, if it does, clean it up and apply some dielectric grease (available at any parts store) to prevent future corrosion, and check for a loose or broken ground wire.

Posted on Apr 13, 2009

SOURCE: brake lights went out, changed bulbs, checked fuse, still wont work

You have to check the brake light switch which should be around the brake pedal on the upperside.
Ones located rremove the wires tht go to the switch and jump them by using a piece of wire, thn check if the brake lights come 'on'. If they do , thn its the switch tht may need replacing or even sometimes adjusting inorder to operate.
Hope this helps.

Posted on May 10, 2009

  • 88 Answers

SOURCE: rear brake lights don't work

you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

Posted on May 23, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2005 grand cherokee brake lights out. changed

checked all fuses even under hood? may have bad signal switch or bad brake light switch yes even if 3rd brake works.also check wiring under rear fender by bumper thats were wire harness is hope this helps.

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the bulb on the passenger side dimer but it still not working.


The fuse my have blow when the bulb did, check and see if you have power and ground at the dome light, if so, check the new bulb for continuity , if not, check the dome light fuse.

Dec 06, 2015 | 2006 Nissan Altima 2.5

1 Answer

2009 V50 back up lights are both out. What could it be? Not the fuse or bulb.


if fuse and bulbs are fine then it's your reverse switch that's not working. it is located at the transmission, change it. but before changing you should make sure that the wires are not cut or faulty.

Feb 08, 2013 | Cars & Trucks

1 Answer

How do i fix the brake lights on my mercury sable. all the other lights work fine


Does your car have the `lamp out'indicator system? It's more complicated.
My manual shows fuse #28 , a 15 amp fuse powers the brake bulbs.Is this the one you changed?
A bulb can be out for a long time and you don't notice it,then the other burns out and you think they both went out at the same time,but they might not have,see?
So check the bulbs and make sure you got that brake switch installed correctly. don-ohio (:^)

Jan 22, 2013 | 2000 Mercury Sable

1 Answer

Head lights work brake lights don't, have changed brake switch and bulbs and checked fuses


When you say you checked the fuse, are you getting power in and out of it and the brake light switch ?

Jan 04, 2013 | 2003 Jeep Liberty

1 Answer

Headlight fault


You may have blown a fuse, check fuses first then before you try to replace the bulb again check for broken wires or the correct bulb

Oct 25, 2017 | 2008 Kia Pro-ceed 1.6

2 Answers

Roof light stopped working


Fuses do not cause bulbs to burn out. You probably have a defective light fixture.

May 28, 2012 | Cars & Trucks

2 Answers

Tail lights do not work all lights work but the back lights do not work. I change the fuse but lights still don't come on. all the other lights work is there other fuses i need to replace


if the bulbs are ok! check bulb socket to see if you have power.with test light, if not make sure sockets are clean. check the bulbs first, because they are a double filiment bulb. for brakes and tail lights. did you change the correct fuse!! it is located in interior fuse box on drivers side end of dash. its on bottom left side of fuse box. its labled "stp lps". hope this helps,

Aug 13, 2010 | 2000 Chevrolet Malibu

1 Answer

No brake lights changed bulbs and fuses


Does the brake light in the rear window work? If so, the brake light switch is good. Running lights all work?

May 24, 2010 | 1998 Toyota Camry

2 Answers

Brake lights not working on 2003 E 350


Have you checked the fuse for the brake lights and have you checked the brake light switch.
The brake light switch is directly above your foot when it is placed on the brake pedal.

Sep 07, 2009 | 2002 Ford E350

1 Answer

Turning Lights Not Working


If you put a 2 element bulb in a single bulb elemet socket you would or could destroy the flasher unit. Especially if it is a electronic flasher try replaceing the flasher but get mechanicl flasher they last longer.

Jul 09, 2009 | 1998 Toyota Sienna

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...