Question about 1997 Eagle Vision

1 Answer

Seeking information to self replace/install new radiator on 1997 Eagle Vision 3.5 ltr. Thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 755 Answers

They are easy to do again youtube

Posted on Feb 03, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: locate fan sensor on 1997 eagle vision

Your fans (low and high) have number of parts.
1. Temputure sensor
2. Hi and Lo fan relays (PCM)
3. Relay located in the fan assembly itself

If you car over heats either in idle or when you turn the air conditioner you are having an eletrical issue. The fix is easy but can take some time, rewireing and a relay.

Hope this helps

Posted on May 18, 2009

  • 116 Answers

SOURCE: 1996 Vision Eagle runs rough and stalls when started

timing belt

Posted on May 19, 2009

  • 72 Answers

SOURCE: where is the oil pressure switch

Under hood, center, front engine area, mounted on driver side lower front of engine

Posted on Jul 04, 2009

emissionwiz
  • 76630 Answers

SOURCE: 1996 Eagle Vision 3.5 idles too fast. How to fix

yes propane or carb spray will work, just spray around the entire intake area and all vacuum hoses, if u hit a vacuum leak the engine idle will change.

Posted on Nov 25, 2009

duane_wong
  • 6826 Answers

SOURCE: were is my thermostat in my 1997 eagle vision

REMOVAL & INSTALLATION

  1. Disconnect negative battery cable. CAUTION
    Do not remove the radiator pressure cap with the cooling system hot and under pressure. Serious burns from hot, pressurized coolant can result.
  2. Allow cooling system to cool completely. Place a pan under the radiator drain, located at the lower right side of the radiator. Open the valve to drain the cooling system to a level just below the thermostat. Do NOT drain the cooling system completely, unless the coolant is being changed. Close the valve.
  3. Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing and if necessary disconnect the hose from the housing. Fig. 1: Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing 88173p06.jpg
    Fig. 2: If necessary, separate the upper hose from the thermostat housing (it is not required) 88173p11.jpg

  4. Remove the thermostat bolts and housing. Fig. 3: Loosen the thermostat housing bolt with the proper size socket 88173p07.jpg

  5. Remove the thermostat and discard the gasket. Thoroughly clean both gasket sealing surfaces. Fig. 4: Separate the housing to access the thermostat 88173p08.jpg
    Fig. 5: Lift the thermostat out . . . 88173p09.jpg
    Fig. 6: . . . then clean the mating area 88173p10.jpg
    To install:
  6. Clean the thermostat housing bolts well. On any engine, bolts that thread into the water jacket are subject to rust and corrosion. A bolt with rust or debris in the threads can easily strip out the threads in an aluminum manifold requiring a time-consuming thread repair operation. Clean the bolts well and lightly lubricate before installation.
  7. Install the thermostat into the recess in the intake manifold. Place a new gasket, moistened with water, on the water inlet mating surface on the intake manifold.
  8. Install the thermostat housing over the gasket and thermostat and tighten the mounting bolts to 21 ft. lbs. (28 Nm) on the 3.3L engine and 105 inch lbs. (12 Nm) on the 3.5L engine.
  9. Connect the upper radiator hose to the thermostat housing and tighten the radiator hose clamp.
  10. Refill and bleed the cooling system.
prev.gif next.gif

Posted on Aug 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is my thermostat in my 1997 eagle vision


REMOVAL & INSTALLATION
  1. Disconnect negative battery cable. CAUTION
    Do not remove the radiator pressure cap with the cooling system hot and under pressure. Serious burns from hot, pressurized coolant can result.
  2. Allow cooling system to cool completely. Place a pan under the radiator drain, located at the lower right side of the radiator. Open the valve to drain the cooling system to a level just below the thermostat. Do NOT drain the cooling system completely, unless the coolant is being changed. Close the valve.
  3. Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing and if necessary disconnect the hose from the housing. Fig. 1: Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing 88173p06.jpg
    Fig. 2: If necessary, separate the upper hose from the thermostat housing (it is not required) 88173p11.jpg

  4. Remove the thermostat bolts and housing. Fig. 3: Loosen the thermostat housing bolt with the proper size socket 88173p07.jpg

  5. Remove the thermostat and discard the gasket. Thoroughly clean both gasket sealing surfaces. Fig. 4: Separate the housing to access the thermostat 88173p08.jpg
    Fig. 5: Lift the thermostat out . . . 88173p09.jpg
    Fig. 6: . . . then clean the mating area 88173p10.jpg
    To install:
  6. Clean the thermostat housing bolts well. On any engine, bolts that thread into the water jacket are subject to rust and corrosion. A bolt with rust or debris in the threads can easily strip out the threads in an aluminum manifold requiring a time-consuming thread repair operation. Clean the bolts well and lightly lubricate before installation.
  7. Install the thermostat into the recess in the intake manifold. Place a new gasket, moistened with water, on the water inlet mating surface on the intake manifold.
  8. Install the thermostat housing over the gasket and thermostat and tighten the mounting bolts to 21 ft. lbs. (28 Nm) on the 3.3L engine and 105 inch lbs. (12 Nm) on the 3.5L engine.
  9. Connect the upper radiator hose to the thermostat housing and tighten the radiator hose clamp.
  10. Refill and bleed the cooling system.
prev.gif next.gif

Aug 19, 2010 | 1997 Eagle Vision

1 Answer

Taking a long time to start engine in the morning.


Coolant temp sensor would be the next thing I would check.

Mar 05, 2010 | 1997 Eagle Vision

1 Answer

Change my hose and got a radiator flush and now my car over heats with the fan running


Check the coolant overflow reservoir and try replacing the thermostat.

Dec 22, 2009 | 1997 Eagle Vision

1 Answer

I want to drain the water from my 97 Eagle Vision Rad so I can fill the resovior with the corect fluid, where is the point of drainage located? Help Please.


Should be a drain valve located on the bottom of the radiator, if not, you may have to just remove the lower radiator hose. Most radiators have drain valves, but there are a few that don't. Hope this helps

Jul 15, 2009 | 1997 Eagle Vision

1 Answer

Locate fan sensor on 1997 eagle vision


Your fans (low and high) have number of parts.
1. Temputure sensor
2. Hi and Lo fan relays (PCM)
3. Relay located in the fan assembly itself

If you car over heats either in idle or when you turn the air conditioner you are having an eletrical issue. The fix is easy but can take some time, rewireing and a relay.

Hope this helps

Feb 28, 2009 | 1996 Eagle Vision

1 Answer

Eagle Vision overheating


look for bleeder screw on thermostat housing or front middle of intake manifold area.open bleeder while vehicle running bleed air out.

Jul 26, 2008 | 1997 Eagle Vision

Not finding what you are looking for?
1997 Eagle Vision Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Stewart Dibbs

Level 2 Expert

322 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...