Question about 1993 Isuzu Rodeo

1 Answer

How to install key ignition - 1993 Isuzu Rodeo

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 389 Answers

Their is a small button to press in on the side of the switch which holds it in the barrel. Press it in with a small screw driver but the button will only press in when the key is in the ignition. Just hold it in while pulling out the old switch from the barrel same procedure to replace.

Posted on Sep 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New key programming for lancer 2005


you need to first install one of factory key into ignition.turn ignition switch on position for 5 seconds.switch off the ignition and remove key.wait 7 seconds insert new key into ignition switch.and switch ignition on until alarm system warning lamp will flash twice mean key programmed. switch ignition off if warning light illuminate for 3 seconds to confirm or flash 3 times indicate registration has failed. if you fail on programming new key let dealership reprogram new keys using diagnostic equipment.

Dec 20, 2012 | 2002 Mitsubishi Montero Sport

1 Answer

How to replace a power steering pump on a 1998 dodge caravan


Hi there:
Check this REMOVAL & INSTALLATION procedure...

CAUTIONThe Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the SIR system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the screws that secure the parking brake release handle to the instrument panel.
  4. Remove the screws that secure the bottom of the lower steering column cover to the instrument panel.
  5. Disengage the retaining clip that holds the right side of the lower steering column cover to the instrument panel.
  6. Remove the lower steering column cover from the vehicle.
  7. Remove the mounting screws that hold the upper and lower steering column shrouds and remove the lower steering column shroud.
  8. Install the ignition key and turn the key cylinder to the RUN position. This is important because it will not only aid in removal of the ignition lock, but will also place the socket (in the lock cylinder housing) in proper alignment for the installation of the replacement ignition lock.
  9. Press in the lock cylinder retaining tab and remove the key cylinder (ignition lock).

To install:
  1. Install the ignition key into the replacement ignition lock key cylinder. Turn the key to the RUN position. Depress the ignition lock key cylinder retaining tab.
  2. Align the shaft at the end of the ignition lock cylinder with the socket in the end of the ignition lock cylinder housing.

  1. Align the ignition lock cylinder with the grooves in the lock cylinder housing. Push the ignition lock cylinder into the housing until the retaining tab sticks through the opening in the lock cylinder housing.
  2. Turn the ignition key to the OFF position and remove the key.
  3. Install the lower steering column shroud and install the mounting screws.
  4. Place the lower steering column cover into correct position on the lower instrument panel and engage the clip that secures the right side of the cover to the instrument panel.
  5. Install the lower steering column mounting screws.
  6. Install the mounting screws that hold the parking brake release handle to the instrument panel.
  7. Reconnect the negative battery cable.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Jul 10, 2012 | Cars & Trucks

1 Answer

LOST ORIGINAL IGNITION KEY ON 1989 MERCEDES BENZ. REPLACEMENT KEY I RECEIVED DOES NOT FIT IGNITION SO ORDERED A IGNITION SWITCH TUMBLER AND NEED TO GET INSTALLATION INSTRUCTIONS ON HOW TO REMOVE OLD...


it would be cheaper to have a locksmith make a key to fit your old ignition lock. I dont know why you didnt do that, before ordering a lock cylinder. Nothing on a MB is cheap. the key is the cheapest thing there is.

Sep 14, 2011 | 1989 Mercedes-Benz 300-Class

1 Answer

How to remove my key lock 2000dodge caravan


Ignition Lock Cylinder - Removal & Installation CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the SIR system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the screws that secure the parking brake release handle to the instrument panel.
  4. Remove the screws that secure the bottom of the lower steering column cover to the instrument panel.
  5. Disengage the retaining clip that holds the right side of the lower steering column cover to the instrument panel.
  6. Remove the lower steering column cover from the vehicle.
  7. Remove the mounting screws that hold the upper and lower steering column shrouds and remove the lower steering column shroud.
  8. Install the ignition key and turn the key cylinder to the RUN position. This is important because it will not only aid in removal of the ignition lock, but will also place the socket (in the lock cylinder housing) in proper alignment for the installation of the replacement ignition lock.
  9. Press in the lock cylinder retaining tab and remove the key cylinder (ignition lock).

    4045958.jpg
    Fig. Depress the retaining tab to remove the key cylinder
To install:
  1. Install the ignition key into the replacement ignition lock key cylinder. Turn the key to the RUN position. Depress the ignition lock key cylinder retaining tab.
  2. Align the shaft at the end of the ignition lock cylinder with the socket in the end of the ignition lock cylinder housing.
  3. Align the ignition lock cylinder with the grooves in the lock cylinder housing. Push the ignition lock cylinder into the housing until the retaining tab sticks through the opening in the lock cylinder housing.
  4. Turn the ignition key to the OFF position and remove the key.
  5. Install the lower steering column shroud and install the mounting screws.
  6. Place the lower steering column cover into correct position on the lower instrument panel and engage the clip that secures the right side of the cover to the instrument panel.
  7. Install the lower steering column mounting screws.
  8. Install the mounting screws that hold the parking brake release handle to the instrument panel.
  9. Reconnect the negative battery cable.

Hope helps (remember rated and comment this).

Aug 11, 2010 | 2000 Dodge Caravan

2 Answers

How do I remove the ignition lock cylinder from a 2003 Saturn Vue for rekeying?


REMOVAL
  1. Disable SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".
  2. Disconnect negative battery cable.
  3. Remove lock cylinder bezel from steering column shroud by carefully prying with thin blade screwdriver.
  4. Remove shroud fasteners and remove steering column upper and lower shroud panels.
  5. Insert key into ignition lock cylinder and rotate to RUN position. Then rotate ignition cylinder back to ACC position.
  6. Depress locking button on side of ignition module assembly with a thin pick-type tool. Slide lock cylinder assembly from ignition module.
INSTALLATION

IMPORTANT: Actuator blade within ignition module housing must be in ACC position to install lock cylinder assembly. If rotated, replace it to ACC position, using needle nose pliers.

  1. Insert key into ignition lock cylinder and install into ignition module.
  2. Install steering column upper and lower shrouds and shroud fasteners.
  3. Install lock cylinder bezel.
  4. Connect negative battery cable.
  5. Enable the SIR system. (Refer to "SIR Disable/Enable Procedure (For Frontal and Curtain Inflators)".

Apr 07, 2010 | 2003 Saturn VUE

2 Answers

96 ford windstar ignition probs


the ignition switch is the electrical part behind the lock cylinder where the key goes in.

Ignition Switch Lock Cylinder
Lock Cylinder Functional
Removal
  1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
  1. Turn the ignition switch lock cylinder to the RUN position.
  1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
Installation
  1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
  1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
  1. Connect the battery ground cable.
-------------------------------------------------------------------------------------
Ignition Switch Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.


71f4c5f.gif


Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and key release lever (if equipped).

Feb 27, 2009 | 1996 Ford Windstar

1 Answer

Ignition key switch


You have to use a pin or paper lip to insert in hole in igmition switch to release the lock cylinder. The key has to be in "on" position I think.

Removal
  1. Disconnect battery ground cable (14301) .
  1. Turn lock cylinder key to RUN position.
  1. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in upper steering column shroud (3530) under ignition switch . Press retaining pin while pulling out on ignition switch to remove it from lock cylinder housing (22074) .
Installation
  1. Install ignition switch by turning it to RUN position and pressing retaining pin. Insert ignition switch into lock cylinder housing . Ensure ignition switch is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit cylinder retaining pin to extend into lock cylinder housing hole.
  1. Rotate ignition switch, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.
871404a.gif

Jan 13, 2009 | 1986 Ford Mustang

1 Answer

1990 Jeep Cherokee Ignition key replacement


Removal & Installation
Without Air Bag
See Figures 1, 2, 3 and 4
  1. Remove the turn signal switch.
  2. Insert the key in the lock cylinder and turn it to the ON position.
0900c152800a9f7f.jpgFig. 1: Using a pair of needle nose pliers, remove the key warning buzzer switch and contacts from the steering column
  1. Remove the key warning buzzer switch and contacts AS AN ASSEMBLY using needle-nosed pliers, or a paper clip with a 90° bend.
0900c152800a9f80.jpgFig. 2: Lock cylinder retaining screwSome steering columns may have a retaining screw holding the lock cylinder in the column. When servicing this type, simply remove the retaining screw and remove the lock cylinder.
0900c152800a9f81.jpgFig. 3: Using a small thin bladed tool, press in the ignition lock clinder retaining tab ... 0900c152800a9f82.jpgFig. 4: ... then pull out the lock cylinder from the steering column
  1. With the ignition switch still in the ON position, insert a thin screwdriver into the slot adjacent to the switch attaching screw boss (right-hand slot). Depress the spring latch located at the bottom of the slot to release the lock cylinder.
  2. Remove the lock cylinder.
To install:
  1. To install the lock cylinder, turn the key to the LOCK position. Insert the lock cylinder in to the housing far enough to contact the drive tang. Force it inward and move the ignition switch actuator rod up and down to align the components. When the components align, the cylinder will move inward and the spring-loaded retainer will snap into place locking the lock cylinder in the housing.
If the lock cylinder is retained by a screw, tighten the screw to 40 inch lbs. (5 Nm).
  1. Install the key warning buzzer switch.
  2. Follow the ignition switch installation procedures to adjust the ignition switch.
  3. Install the turn signal switch.
With Air Bag
Please refer to the ignition switch removal and installation procedure.50c573d.jpg73cc55f.jpgb9448d0.jpg278f367.jpg

Oct 22, 2008 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...