Question about 2002 Nissan Quest

1 Answer

Wire hassnest for a/c speed control

Wher is the wire hassnest for a/c speed control from slow to fast

Posted by on

  • celfishing1 Sep 09, 2009

    I changed the fan control swich and it only run on high can not control a lower speed 2000 nissan quest

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

This is vacuum controlled. It's vacuum lines go from the control switch to an actuator.
If your kinds has a harness for the control circuit on the back of the control switch, then you will need to pull out the control switch panel to access it.

Posted on Sep 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

200 dodge ram all electrical diagram including radio


Go to the link for diagrams. http://bbbind.com/free_tsb.html


Have you run an engine control module fault code test? Have you cleaned the throttle body and idle speed control valve?

Apr 26, 2017 | Dodge Cars & Trucks

1 Answer

Wipers stoped working on slow speed and intermitant speed but ok on fast speed


it could be the switch or the wiper intermitant control relay.

Aug 14, 2015 | Cars & Trucks

3 Answers

Wipers only work on fast. Checked the relay and its good, checked the switches and its good. What else needs to be checked?


This is (obviously) a two-speed motor. The low speed winding is burned out. Replace the motor.

Sep 09, 2014 | 2007 Ford Bantam 1.3i

1 Answer

2000 mercury villager, runs a fast idle. whether cold or warm the idle remains at a high idle speed, it even pulls with the brake applied.


Could be a vac leak, or a dirty throttle body, or a faulty idle air control valve. The computer controls idle speed by regulating the amount of air into the intake. Could also be something pulling on the throttle cable such as the cruise control.

Sep 28, 2012 | 2000 Mercury Villager

1 Answer

1985 gmc k1500 wipers only move at 1 slow spped, interminttent doesnt work at all. How fast is fast and why is fast not working?


Slow is the same speed as 'mist'. Mist is when you twist the control arm backwards to induce a single swipe. If you hold it, you will run the wipers in low speed. Fast is faster than that. Probably by 30% or more.

Turn the wipers on high speed. Wiggle the connector at the wiper motor. If the wipers run sporadically as you wiggle the connector, you either have a bad connector or a bad circuit board on the wiper motor.


Jan 15, 2010 | 1985 GMC K1500

1 Answer

Intermittent blower speeds


pull motor ,check for burned wires onfan and bak of fan speed switch,fan could be the problem un hook fan and conect directley to 12 volts and see if varibles exsist,if so replace fan motor/look for a fan resister if all the other things check out

Jul 03, 2009 | 1999 Chevrolet Suburban

1 Answer

I have 1991 honda accord, heater blower motor does run but very slowly in all speed positions i have removed the blower assbly. and motor seems to turn free. is there a speed control that may be bad ?


If you have removed the blower motor, Connect it to a 12 volt power supply(your battery)with some jumper wires.It should turn fast, be careful when you connect it, have a good grip on it, it will jump just a little. If it dont run fast its junk. The other 2 things
1)The fan switch
2) The resistor that slows the fan at low speeds.

Jun 14, 2009 | 1995 Honda Accord

1 Answer

Wiper Speed changes from slow to fast then back to slow without moving switch!


the reason for your wiper speed change is due to the rain sensor which controls the speed of your wipers,determined by how much rain is comming down.the rain sensor is located behind your rear view mirror.

Sep 27, 2008 | 1997 Buick Park Avenue

2 Answers

Wipers only work on fast speed no intermittent or slow wipe


The common way of controlling wiper speed is to use a 'tapped' resistor that supplies reduced voltage to the wiper motor on all but the fast setting.
They have to dissipate a good bit of heat and are subject to failure; I think yours has done that.

Aug 26, 2008 | 1994 Honda Civic

Not finding what you are looking for?
2002 Nissan Quest Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...