Question about 1998 Toyota Camry

1 Answer

How do i remove back rotor to install new lug

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 507 Answers

Take off rear caliper(may need to disconnect handbrake)if caliper doesnt come off easily,then remove disc or drun,probably disc,knock stud in and it will come ouy,fit new one and use wheel nuts to pull it in to the hub,then fit disc and caliper and wheel

Posted on Nov 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front brake pads


1. Raise vehicle
2. Support on jack stand
3. Remove lug nuts
4. Remove wheel
5. Remove bolts holding caliper
6. Remove calipers
7. Remove brake pads
8. Push piston into caliper
9. Inspection rotor for damage if damaged replace
10. Install new pads
11a. Replace caliper on rotor
11 b. Replace bolts in caliper and tighten
12. Bleed brakes
13. Replace wheel
14. Replace lug nuts
15. Lower vehicle
16. Tighten lug nuts
17. Test drive vehicle

Oct 17, 2015 | 2004 Chrysler Sebring

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

Replace rear brake pads 2006 Chevy Impala


Hello, to replace the rear brake pads follow the following steps:

1. Lift the Chevy Impala with the jack and place it on jack stands.
2. Remove the wheels with a lug-nut wrench and set them aside. The lug-nut wrench can be found in the trunk of your Chevy Impala.
3. Remove the caliper with a ratchet and use a bungee cord to hang the caliper. Do not let the caliper hang from the brake hose, as the hose might break and cause fluid to leak.

4. Remove the brake caliper bracket from the steering knuckle with a ratchet. Set it aside.

5. Remove the break rotor from the hub. The rotor might require force to be removed; if it does, use a hammer to hit the rotor in the center, where the lug studs are located. Take care not to hit the studs.

6. Remove the new rotor from its packaging and use brake cleaner to remove the grease from the rotor. Grease is applied on the rotor in the factory to inhibit rust during storage.

7. Install the new rotor onto the hub.

8. Install the caliper bracket with new brake pads onto the rotor and fasten it to the steering knuckle. Use a ratchet to tighten the bolts.
9. Open the master cylinder reservoir so you don't break a seal while compressing the brake caliper.

10. Compress the brake caliper with a C-clamp, so that the caliper can fit over the new brake pads. Install the caliper by securing it to the brake caliper bracket with a ratchet.

Thanks


























Jul 19, 2010 | 2006 Chevrolet Impala

1 Answer

We had a new serpentine belt replaced a couple of months ago and it just came off. How can I put it back on? Also the lug nuts seem to be stripped.


Click on the following free direct Link. It has the Serpentine Belt Diagram and Tensioner location for your 2000 Saturn SL.

http://www.2carpros.com/car_repair_information/year/2000/make/saturn/model/sl/2000_saturn_sl_drive_belt_routing_diagram.htm

Before we get to putting it the Belt back on...
Look at the alignment of the Pulleys. Most times the Tensioner or Idle Pulley are "canted" - meaning pitched or leaning forward, which causes the belt to "run off" the pulley - throwing the belt.
With the Belt off: check side-to side play for each one of the Pulleys by hand, especially for the Tensioner and Idle Pulleys. There should not be any side-to side play. If there is any other Pulleys that are canted - check if they are properly tightened. A new belt should not have come off on it's own without some other problem.

GENERAL/Standard Rules to Removal the Serpentine Belt with a Tensioner:
A. Find the Tensioner(s). (See Diagrams on Link)
B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
C. Remove the loosened belt off one of the other more easily accessed Pulleys.
D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


Regarding the Strip Lug -Studs.
Is this on the wheels with Rotors (Disc) or Drums? If the tire was not properly mounted, or the Lug Nuts were not properly Torqued; this will cause the Lug Studs (bolts) to be stripped.
With the vehicle raised and properly supported by jack stands:
For Rotors:
Remove the Tire, Brakes (Calipers/Pads) and Rotor, exposing the Wheel Hub (Bearing) Assembly with the Studs fully exposed. Rotate the Wheel Hub to a location where the Lug Studs can be clearly removed FROM THE REAR OF THE WHEEL HUB ASSEMBLY.
Using a impact hammer or mini sledge hammer: Hammer the Lug Studs back thru the Wheel Hub Assembly.
Remove the loosened Lug Studs.

For Drums:
Raise, support, remove the Tires.
Remove the Drums off the Wheel Assembly.
Using a impact hammer or mini sledge hammer: Hammer the Lugs back into the drum, removing from inside the Drum

Purchase the new, correct size and length Lug Studs and new Lug Nuts. If the Studs were stripped, most like the Nuts are too.
To reinstall the Lug Studs: Purchase an additional two (2) Lug Nut that fits that Lug Stud. Also purchase several Large Heavy Duty Washers that can fit on the the Lug Studs.

Place the Lug Stud back into the Wheel Assembly from the Rear (Rotors) or from inside (Drums). Use High Temp Grease for the area of the Lug Stud Splines that have to be "drawn" into the Wheel Assembly (with Rotors) or into the Drum.
After the Lug Studs are "IN" as far as they will go: on the outside place at least two (2) of the Washers on Lug Studs. Use a Lug Nut and tighten as far as possible down-on the Lug Stud as possible.
Next: Using an Impact Wrench tighten that Lug Nut down/on, drawing the Lug Stud into the Wheel Assembly/Drum. Check the rear of/inside the Wheel Hub Assembly/Drum. The Heads of the Lug Studs should be firmly against the Wheel Assembly/Drum.
If you do not have a Impact Wrench - use at least a 24-in Breaker Bar and Tighten the Lug Nut on, drawing the Lug Stud into the Wheel Hub Assembly/Drum. This takes longer and alot more work, compared to 10-seconds using the Impact Wrench.
Repeat as necessary.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Mar 31, 2010 | 2000 Saturn SL

3 Answers

I have sheared a front wheel lug on my 1995 landcruiser Amazon. Friends had a puncture and didn,t tighten wheel nuts properly on spare. How do I replace.


The lug nuts are press fitted in the rotor. You should be able to hit the bolt with a hammer(or hammer and punch if the bolt is sheered flush with the rotor) and it should come out.

Jan 17, 2010 | 1995 Toyota Land Cruiser

2 Answers

I have a 95 Chevy suburban and I am trying to change the rotor and can not get it off. The lugs are attached to the rotor and not sure what I should do


Removing: Loosen lug nuts (7/8") and spindle nut (36mm). Lift truck. Remove lug nuts, spindle nut, and wheel. Remove 2 bolts (3/8" allen) holding calipers on. Hold the calipers up with a bungee cord. I attached it to the sheet metal of the fender. Remove 4 bolts (15mm) from rear of hubs. Once these bolts are removed you can move the shield that is in-between the hub and the axle(I think). You are moving it to get access to the allen bolt that holds the ABS sensor on. Once you move the shield then you can look through the top of the rotor through the slots and see the sensor line and bolt. I don't remember what size allen this one took. You do need a long allen wrench though. Disconnect sensing line from hub. Now the rotor is ready to come off. I had to use a pry bar to remove this gently working each side until it popped off. Once the rotor is removed, you need to hammer out the lug bolts. Then you have to tap the rotor away from the hub. This took a little work. Then check each of the lug bolts by screwing the lug nuts on them. They should go all the way down by hand. If they don't - go buy new bolts $2 a piece. Installing: Position new rotor on hub. Get some dry ice from your local grocery store and freeze the bolts for about 10 minutes. Pull one bolt out of the ice at a time and install on the rotor and tighten the bolt with the lug nut. I put the nuts on upside down and used a 7/8" wrench and mallet to tap on the wrench to get these as tight as possible. You also have to tap on the head of the bolt and repeat the wrench tapping. Do this for each bolt pulling one out of the ice at a time. You do not have to get the rotor and hub completely together but get it as close together as possible. Once all of the lug bolts are in it is time to put the rotor on the truck. Ensure the shield is on the spindle and install the rotor, again, this takes some work. Once the rotor is on, connect the ABS sensing line. Line up the shield and install 4 bolts to rear of hub. You can align these by moving the hub, not the rotor. Install the caliper, remember to put brake grease on these 2 bolts. You may have to compress the caliper slightly. To do this remove the brake pad that has the circular part of the caliper touching it. Open the brake fill cap on the master cylinder. Use a C-clamp to compress the circular part. Reinstall the brake pad and brake fill cap. Install the caliper. Install the wheel and tighten lug nuts. I used a cheater bar on my tire iron and ensured that the lug bolts were flush with the head of the lug nuts. Then I removed the wheel to verify that the gap between the rotor and the hub was gone. Reinstall wheel, tighten lug nuts, and tighten spindle nut. Once both brakes have been replaced, start up the truck and pump the brakes several times till you feel some tension when pressing them.

Nov 25, 2009 | 2000 Dodge Durango

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

2 Answers

Instructions to replace sheared off lugs / studs - 1997 Chevy


You can remove old lug by driving it out with a decent sized hammer. To re-install, push new one into flange from backside and stack washers on wheel side, leaving enough room for the lug nut to go on. (backwards...flat side in) Tighten the nut, pulling the lug into the flange, till it is flush (like the unbroken ones) I suggest that you put some lube on lug threads to prevent binding while doing this.

Mar 16, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...