Question about 1992 Chevrolet Cavalier

2 Answers

Is there a special tool needed for the removal of a 92 cavalier hub assembly. there seems to be a large square bolt with 4 square inserts, 2 recessed, 2 not

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

U will need a torx socket,number T55

Posted on Sep 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 298 Answers

Hi there called tork wrench

Posted on Sep 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front right bearing on my 99 hyundai elantra needs replaced. how hard is it?


IF IT IS DISK BRAKES, NOT HARD! JACK IT UP. REMOVE TIRE. ON BACK OF DISK BRAKE HOUSING IS TWO BOLTS. REMOVE THOSE, AND REMOVE DISK BRAKE SYSTEM FROM HUB. TAKE DUST CAP OFF HUB. REMOVE LARGE NUT. MAY NEED TO REMOVE COTTER KEY FIRST, THEN NUT COVER. FRONT BEARING, AND WASHER WILL COME OUT WHEN YOU WIGGLE DRUM. TAKE DRUM OFF, AND TURN OVER. REMOVE SEAL, AND REAR BEARING. YOU'LL HAVE TO GET A NEW SEAL FOR THAT PART. GREASE NEW BEARINGS, AND REPLACE THEM! THE NEW SEAL CAN BE TAPPED IN WITH A RUBBER HAMMER, OR HAMMER TILL IT IS LEVEL WITH THE RING IT GOES INTO! THEN PUT HUB BACK ON SPINDLE, AND REVERSE DIRECTIONS TILL IT IS COMPLETE!

Feb 20, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Need to replace 2003 corola front wheel bearings. need step by step instruction please


Removal & Installation To Remove:
toy_car_cor-02-04wheelhub1.gif

  1. Remove the front wheel.
  2. Remove the front axle hub nut.
  3. Disconnect the front stabilizer link from the strut.
  4. Disconnect the speed sensor (with ABS).
  5. Remove the front brake caliper and rotor.
  6. Disconnect the tie rod end.
  7. Remove mounting bolts and nut and separate the lower control arm from the ball joint.
  8. Using a plastic hammer separate the front axle shaft from the hub.
  9. Remove the 2 mounting bolts from the strut. Remove the knuckle and hub assembly.
  10. Remove the lower ball joint from the knuckle.
  11. Remove the axle hub snap ring from the knuckle. toy_car_cor-02-04wheelhub2.gif

  12. Remove the axle hub from the hub bearing using special tool 09520-00031 or equivalent hub puller.
  13. Remove the inner race from the axle hub using special tool 09950-40011 or equivalent puller.
  14. Remove the dust shield from the knuckle.
  15. Remove the axle hub bearing from the knuckle using special tool 09520-00031 or equivalent and a press.
To Install:
  1. Install the axle hub bearing on the knuckle using special tool 09950-600020 or equivalent and a press.
  2. Install the dust shield on the knuckle with 3 mounting bolts.
    • Tighten 73 in-lb (90 Nm).
  3. Install the axle hub on the knuckle using special tool 09950-600010 or equivalent and a press.
  4. Install the axle hub snap ring.
  5. Install the lower ball joint on the knuckle.
    • Tighten the ball stud castle nut 76 ft-lb (103 Nm).
  6. Install a new cotter pin.
  7. Install the knuckle on the strut with the 2 nuts and bolts.
    • Tighten 162 ft-lb (220 Nm) (except '03-'04) 113 ft-lb (153 Nm) ('03-'04).
  8. Lift the knuckle and hub assembly over the axle shaft and into the hub splines.
  9. Install the lower control arm on the lower ball joint.
  10. Connect the tie rod end to the knuckle.
  11. Connect the stabilizer link to the strut.
  12. Install the front rotor and brake caliper to the knuckle.
    • Tighten the 2 caliper bolts 79 ft-lb (107 Nm).
  13. Install the ABS sensor if equipped.
  14. Install the front axle hub lock nut.
    • Tighten 159 ft-lb (216 Nm) and stake the lock nut.
  15. Check the axle hub backlash and run-out.
  16. Install the front wheel.
  17. Check the front wheel alignment and adjust if necessary.
prev.gif next.gif

Feb 17, 2011 | Toyota Corolla Cars & Trucks

2 Answers

How easy is it to replace a front wheel bearing assembly? and also a diagram if possible.


It's not too involved. Here's a link with some more information to change it:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528025fae3

Nov 05, 2010 | 1994 Pontiac Grand Am

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

How technical is it to replace a front wheel bearing on a 2005 Pontiac SV6 and can I do it without any specialized tools


you will need a big socket (20 or 21 mm) and 1/2 inch drive to remove axle nut and torque wrench to reinstall. The book DOES call for a special tool to get the hub off the axle, but I have never used one before.


Removal & Installation


  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the wheel drive shaft nut.
  4. Remove the brake caliper and wire aside.
  5. Remove the brake rotor.
  6. Disconnect the electrical connector from the wheel speed sensor.
  7. Remove the wheel speed sensor connector from the bracket by depressing the locking tabs.
  8. Remove the 3 hub and bearing assembly bolts.
  9. Install Wheel Hub Removal tool J-42129 to the hub and bearing assembly in order to remove the hub and bearing assembly from the wheel drive shaft.
  10. Remove the hub and bearing assembly from the steering knuckle.

To install:
  1. Install the hub and bearing assembly to the steering knuckle.
  2. Install the 3 hub and bearing assembly bolts and tighten to 85 ft. lbs. (115 Nm).
  3. Install the wheel speed sensor connector into the bracket until the locking tabs click into place.
  4. Connect the electrical connector to the wheel speed sensor.
  5. Install the axle nut to the wheel drive shaft and hand tighten.
  6. Install the brake rotor.
  7. Use a screw driver or similar tool to stop the rotation of the brake rotor.
  8. Tighten the wheel drive shaft nut to 159 ft. lbs. (215 Nm).
  9. Install the brake caliper.
  10. Install the tire and wheel.

Sep 24, 2010 | Pontiac Montana SV6 Cars & Trucks

3 Answers

Right front wheel bearing is bad how do I change it


  1. Raise and support the vehicle safely. Place jackstands under the frame, then lower the vehicle slightly to allow the control arms to hang free.
  2. Remove the tire and wheel assembly.
  3. Insert a drift punch into the caliper and rotor vanes to prevent the rotor from turning, then remove the hub/drive axle nut. Clean the threads of the nut.
    1. Unfasten the caliper mounting bolts, then remove and support the caliper aside with a suitable piece of wire.
    2. Remove the rotor by sliding it from the hub.
    3. If equipped with ABS, detach the front wheel speed sensor connector and unclip it from the dust shield.

    The hub and bearing are replaced only as an assembly.
    For 1987-92 vehicles, perform the following:
  4. Using a suitable front hub spindle removal tool, separate the hub from the halfshaft.
  5. Remove the hub and bearing retaining bolts, shield, hub and bearing assembly and the O-ring.
  6. Separate the ball joint from the steering knuckle, using the proper tool.
  7. Remove the halfshaft assembly and tap the seal from the steering knuckle. Remove the steering knuckle from the hub.
  8. For 1993-99 vehicles, perform the following:
    1. Unfasten the hub and bearing retaining bolts and dust shield.
    2. Place the transaxle in PARK.
    3. Using a suitable front hub spindle removal tool, separate the hub and bearing from the drive axle.
    4. If necessary, remove the steering knuckle.

  9. Clean the rust and foreign material from the knuckle mounting face, bore and chamfer to allow the bearing to properly seat in the knuckle.
To install:
  1. For 1993-99 vehicles, perform the following:
    1. If removed, install the steering knuckle.
    2. Position the hub and bearing assembly to the drive axle. Apply a light coating of grease to the knuckle bore. If the new hub and bearing has a protective plastic cover, remove it before installation. Also, do not handle the knuckle or hub assembly by the ABS sensor wire.
    3. Install a new drive axle nut and draw the hub and bearing onto the axle.
    4. Place the transaxle in NEUTRAL.
    5. Install the dust shield, being careful not to damage the bearing outboard lip seal.
    6. Install the hub and bearing bolts, then tighten to 70 ft. lbs. (95 Nm).

  2. For 1987-92 vehicles, perform the following:
    1. Install a new hub and bearing seal in the steering knuckle with a suitable seal installation tool. Install the steering knuckle to the strut.
    2. Lubricate the hub and bearing with grease. Fill the cavity between the seal and bearing completely.
    3. Install the halfshaft.
    4. Connect the ball joint to the steering knuckle and insert a new O-ring around the hub and bearing assembly.
    5. Install the hub and bearing, and shield into the steering knuckle. Tighten the bolts to 70 ft. lbs. (90 Nm).

  3. If equipped, attach the ABS front wheel speed sensor connector, then clip the wire to the dust shield.
  1. Install the rotor and caliper assembly. Tighten the caliper bolts to 38 ft. lbs. (52 Nm).
  2. Insert a drift punch into the caliper and rotor vanes to prevent the rotor from turning. If not already done, install the shaft washer and nut (if equipped). Tighten the nut to the following specifications:
  3. 1987-88 vehicles: 3 ft. lbs. (270 Nm).
  4. 1989-90 vehicles: 15 ft. lbs. (260 Nm).
  5. 1991-99 vehicles: 107 ft. lbs. (145 Nm).
  6. Install the tire and wheel assembly.
  7. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (136 Nm).
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 21, 2010 | 1995 Buick LeSabre

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

How to replace 99 gmc 3/4 tom brake rotors


Removal & Installation
  1. Remove 2/3of the brake fluid from the master cylinder.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Remove the front wheel hub extension (dual wheel vehicles only).
    • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
    • Mark the relationship of the front wheel hub extension to the hub
    • Remove the front wheel hub extension bolts
    • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
  5. Mark the relationship of the rotor to the hub.
  6. Remove the caliper and mounting bracket as an assembly.
  7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
  8. Remove the rotor.
  9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
    • Clean all the surface areas and the threaded holes of contamination
    • Generously apply penetrating oil or the equivalent to the hub/rotor area
    • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
    • Tighten both bolts evenly to force the rotor from the hub.
c3692a2.gif
To install:
  1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
    NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

  2. Install the rotor.
  3. Install the caliper and the mounting bracket as an assembly.
  4. Install the tire and wheel assembly.
  5. Remove the safety stands.
  6. Lower the vehicle.

Oct 25, 2009 | 1999 GMC Sierra

1 Answer

How do I change the rotors on a 1996 F250 4wd truck?


CHANGING BRAKE PADS AND ROTORS
Changing the brake pads is pretty easy, after you remove the tire locate the two large bolts on the back side of the caliper i think they are 13/16 heads. remove these two bolts. after the bolts are out use a pry bar to work the caliper straight up off the rotor, slide the pads out of the caliper and compress the piston in the caliper, this can be done with a large c-clamp if you dont have a piston compressor (use the old brake pad as a buffer so you dont damage the piston).
4x2 remove the dust cap in the center of the hub use a pair of dikes to straighten and remove the cotter pin thats locks the castle nut in place then remove the castle nut (can be done with channellocks if you dont have large enough socket) slide the hub off the spindle careful not to drop the bearing and washer on the ground. *** put the lug nuts back on the studs up side down and flush them to the end of the stud if you still hve the stock open lug nuts if not then just be sure to hit the studs square so you dont damage the threads. place the hub on hard solid ground rotor side down and knock the studs out with a fairly good size hammer. reverse process to assemble
4x4 this is a little more difficult than 4x2 you will need some specialty tools (torqs, picks, snap ring pliers, and a 2 3/4 inch rounded hex socket) these instructions are for a stock ford automatic hub. remove the outer hub (three small torqs bolts). use a small to medium straight screwdriver to remove the first locking ring (inside lock) slide the inner hub assembly out of the hub. remove the outside snap ring from the axle shaft slide the three washers of of the shaft keeping them in order. there will be a small half circle keeper on the large nut remove this with a pick use the 2 3/4 socket to remove the hub nut slide the hub off the spindle careful not to drop the bearing and washer on the ground then follow the 4x2 instructions.

Oct 15, 2009 | 1995 Ford F250

Not finding what you are looking for?
1992 Chevrolet Cavalier Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...