Question about Chevrolet Nova

1 Answer

Torque spec's: 75 nova steering components

Need torque spec's: 75 nova steering components. replacing idler arm center link and inner - outer tie rod ends.

Posted by on

  • Anonymous Mar 31, 2014

    have a street rod with nova 8.2 rear need to know how to adj rear brakes

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,002 Answers

I looked in an old Motor book, competitor to Chilton, and it gives no special torques or instructions for front end parts. It just says tighten.From experience I always tightened them with a 3/8 socket wrench until they stopped turning using just my arm strength. Never loosen to put in a cotter pin. Hope this helps.

Posted on Sep 10, 2009

Testimonial: "75 nova dude: problem solved THANKS!! to hippycy"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many lubrication fittings are there on a 1999 Buick LaSabre?


if this has a conventional front end(not front wheel drive) then there will be one on each outer tie rod end one on each inner tie rod end, both upper and lower ball joints on each side, idler arm and pitman arm. if its front wheel drive it will have a rack and pinion steering. there for there will be one on each outer tie rod end and one on each lower ball joint, if they have grease fittings. so conventional steering has 10 fittings total and rack and pinion has 4 total.

Jul 28, 2015 | Buick Cars & Trucks

1 Answer

What's the outer tie rod end torque specs for 2000 Dodge Dakota sport ?


this was copied off of the following link. should be same torque requirments-
this is off a 2004 manual,which should be real close if not exact

INSTALLATION
1. Align reference marks and install pitman arm.
2. Install the lock washer and retaining nut on the pitman
shaft and tighten nut to 251 N·m (185 ft. lbs.).
3. Install the drag link (1) to the pitman arm (5). Install
the nut (4) and tighten to 54 N·m (40 ft. lbs.) Then
an additional 90°.
4. Remove the supports and lower the vehicle to the
surface. Center steering wheel> and adjust toe,
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
5. After adjustment tighten tie rod adjustment sleeve
clamp> bolts to 61 N·m (45 ft. lbs.).
NOTE: Position the clamp on the sleeve so retaining
bolt is located on the bottom side of the
sleeve

got it from here -

Tie rod end torque spec DodgeTalk Dodge Car Forums Dodge Truck Forums and...

Feb 23, 2015 | Dodge Cars & Trucks

1 Answer

How to change front end on 94 gran marquis


Front end is a pretty vague description of what you are trying to do. There are - shocks -lower ball joints -upper ball joints -inner tie rod ends -outer tie rod ends -idler arm -pitman arm -center link -stabilizer links -stabilizer bars It is not likely that all of those need to be replaced at the same time?

Apr 10, 2013 | Cars & Trucks

1 Answer

I need to replace inner and outer tie rods and Idler arms. Is there a diagram?


The inner and outer tie rods are pretty self explanatory remove the nut from the knuckle. Whack the knuckle a couple times where the tie rod goes through and the tie rod will pop out. The inner will releas the same way. Get the sleeve whe you get the inner and outer tie rod. It will make life a lot easier. Assemble the new parts to the approximate same length as the parts you removed and install. The idler arm will be bolted to the frame and then have a ball and socket that will be removed in the same manner as the tie rod end. The pitman arm will require a puller to seperate it from the gear box. Sometimes you have to heat up the end that attaches to the gear box to get them to pop. Sometimes the gear box needs to be removed in order to get the puller on the pitman arm. Lower and upper ball joints are also very common on these. If they have not been done I would have them checked as well.

Aug 07, 2012 | 2000 Chevrolet Blazer

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

1991 C1500: I am replacing the tie rods on my 1991 Chevy C1500...


The inner holes, the inner tierod ends go into the outer holes.

May 16, 2010 | 1991 Chevrolet C1500

1 Answer

How to change the pittman arm and idler arm on a 1999 S10 Chevy Blazer 4x4?


Pitman arm requires a pitman arm puller, and a tie rod seperator or "pickle fork". Remove the cotter pin on from the joint on the pitman arm and center link, then remove the nuts from both ends of pitman arm. Use the pitman arm puller to remove the pitman arm from the steering gear, then use the tie rod seperator to remove the end from the center link. Reinstall and retighten nuts, do not leave out the cotter pin.
Idler arm will require tie rod seperator. Remove the cotter pin from the end at the center link, use the tie rod seperator to seperate the joint there. Unbolt the idler arm from the frame, and remove. On reinstalling remember to install a new cotter pin. It would be best to have the front end alignment checked after replacing these parts.

Apr 08, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

1 Answer

Loose steering


Idler arm, pitmen arm, and tie rod ends, ball joints.

Feb 10, 2009 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...