Question about 1996 Honda Accord

1 Answer

1996 Honda accord doesn't know how to replace front wheel broken bolt?

Posted by on

  • peter170 Sep 30, 2009

    I got a 1990 honda accord i need to replace the the wheel bearing? Whats my frist step to replace the bearing. How do i get started.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

Remove the spindle, take it to a shop with a press, have them press off the hub, replace the broken wheel stud and reinstall.

P.S. If it is a one piece like quite a few accords are, then you may need a bearing as well due to the breakage rate when they are removed.

Hope that helps.

also, 80 lbs/ft is plenty of torque for the lug nuts on any honda car.

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a broken valve cover bolt on a 96 honda accord?


remove cover again, drill small hole into bolt if it is broken off too close to get with vice grips, use ez out very casrefully.


place some sort of rags or towels to catch metal shavings, can also spay shave cream on top of rags or towels to help catch metal shavings.


these bolts are only ten mm so only take about 7 pounds of torque. tighten in criss coss fashion little by little evenly.

Sep 20, 2014 | 1996 Honda Accord

1 Answer

What is the length of a 196 Honda Accord 4 door sedan?


Don't know what yours is, but it is measured by the wheel base. Measure from the center of the wheel front to back.

Sep 10, 2011 | 1996 Honda Accord

1 Answer

I need to know how to take out the front rotors coz everytime i brake, my steering wheels shaking


ON THE 95 AND 96 ACCORD THE ROTORS WERE BOLTED TO HUB. ITS A JOB! U NEED A HUB REMOVER,AXLE NUT SOCKET AND METRIC TOOLS. IF U NEED STEP BY STEP I CAN CLARIFY. IT TAKES ABOUT 2-3 HOURS A SIDE DEPENDING ON HOW EXPERIENCED U ARE

Aug 04, 2010 | 1996 Honda Accord

1 Answer

Help i have a broken wheel stud on the front wheel of a 1996 accord how do i replace


It is a fairly easy fix, sometimes, Most studs just knock right out the back, put in the new one and tighten it up. Some, not so easy, some you have to take off the spindle, some are clipped in, some threaded, so you need to find out what you have there before you start fixing. I would go to the auto parts store and ask for one and then ask how it goes in. They should be able to show you. Hope this helps.

Aug 01, 2010 | 1996 Honda Accord

2 Answers

How do you replace the front rotors on a 1996 honda accord?


Remove wheel. Take off outer driveshaft nut. Remove lower ball joint pinch bolt & separate ball joint from spindle. Pull rotor & spindle out & away to pull driveshaft outer splined end out of rotor center hub. Look on the back of the spindle for the 4 bolts that hold in the wheel bearing. Use a 12 point socket to remove the 4 bolts and remove wheel bearing from spindle (out towards the wheel stud side). Probably will have to use a air chisel to get it out. Once it's out undo the 4 bolts on the outer (wheel stud side) of the rotor and remove the rotor from the hub. Clean & lube the hole where the bearing was in the spindle & the inner face of the hub. MAKE SURE IT'S CLEAN otherwise you may get a pulsation on braking if theres a piece of rust or dirt between the rotor center & the hub face. Reverse procedure to install.

If the rear bolts don't come out then you will have to use a slide hammer to separate the bearing to replace the rotor and there is a very good chance you will need to replace the wheel bearing after you're done (noisy on road test).


Not the job to do at home, usually an easy 2-3 hours per side if things go bad (book time is 2.2 hrs per side). Use good quality rotors as you don't want to have to do it again because a cheap rotor gave you a pulsation.

May 28, 2010 | 1996 Honda Accord

1 Answer

I need to change right front wheel bearing on 96 honda accord


It's not a easy job you will need a press to take the old one out and replace the new one, my advice to you is take the steering knockle out and have your local shop press the bearing out for you and put the new one in. This way you just have to bolt everything back up and your good to go.

Oct 20, 2009 | 1996 Honda Accord

1 Answer

T would like to know the steps to remove the front rotors.


You can try a couple of things. First the most common is try spraying it with something like WD40 or get a breaker bar which will give you more power to turn it and will add alot more tension so the bolt will break loose. Could be that the heat seized it there but try these steps.

Mar 23, 2009 | 1996 Honda Accord

2 Answers

1996 HONDA ACCORD HOW DO I REPLACE THE FRONT ROTORS


  1. the rotors are held on by the wheel mainly
  2. to replace remove wheel
  3. remove caliper
  4. if brake pad cage raps around rotor remove with 2 bolts from backside
  5. take big hammer and tap surface of rotor near wheel studs use care not to hit studs. one or two good smacks should break rotor free from rust

Nov 15, 2008 | 1996 Honda Accord

1 Answer

1996 accord headlight replacement


hi you have to remove the bumper but not a big job as it is only the cover a screw under each wheel arch three clips in the middle and a set of clips and ten millimeter headed bolts yates210456

Sep 20, 2008 | 1996 Honda Accord

1 Answer

Replace front wheel bearings


Front wheel bearing on a Honda Accord are a press in unit. It is a project that is not for the faint of heart.

Aug 07, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...