Question about 1998 Ford Mustang

1 Answer

Gear shift won't come out ofg park, with the key in or out ignition on or off.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,741 Answers

Look for transmission shift interlock solenoid fuse.or a bad brake switch will cause transmission not to come out of park. --------------------- Most automatics require the depression of the brake pedal before the shifter will release out of park.

The other thing that could prevent this is that you are possibly parked on a slant and didn't set the parking brake. The little pin in the tranny is all that is holding your car from rolling - there's lots of pressure resting on that pin, so it may take lots of force to get it to move. Always, always, set the manual parking brake in automatics on hills .
----------- its because broken transmission cable.the transmisson cable needs to be replaced. --------------- also another reason can be a faulty brake switch that is connected to the brake pedal. You normally step on the brake to place the car in gear. If the switch goes out and you step on the brake the trans will not engage. ---------- also another reason can be wrong parking ----- you must have put the car in park and let the car roll before engaging the hand brake. If your car rolled while in park and the weight of the car leaned on the parking brake you may need to push the car a little bit before it can get out of park. depending on the car the push may need to be a little or a lot. Next time follow this as a parking routine: reverse or drive into parking spot, stop, with foot still on the brake pedal put car in park and engage hand brake fully so that car doesn't roll. Remove foot from brake pedal. This should stop that problem. ------------ this will help.thanks.please do rate the solution.thank you for using fixya.keep updated.

Posted on Sep 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Volvo S40 cannot remove key


What make vehicle ? Most all vehicles have a safety system .Don't try an force anything you'll break it !
Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. They also have this on column mounted shifters !

Aug 19, 2015 | Cars & Trucks

1 Answer

The Key FOB is stuck in the ignition. How can I get it to eject?


Most if not all vehicles have a Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. Or it has
Linear Shift Assembly: If the vehicle is equipped with a column mounted gear shift, it has a linear shift assembly on the steering column. The linear shift assembly has a cable that runs from the linear shift assembly to the ignition lock cylinder case. The purpose of this cable is to prevent the ignition key from being turned to the OFF position when the transmission is in gear and the vehicle may still be moving. The linear shift assembly cable contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.
Your best bet is to take it to a ASE certified repair shop or the dealer ! The fix involves taking the steering column apart an or the floor shifter assembly ! Also electrical test to determine what is the problem !
Your

Jul 04, 2015 | 2008 Volvo S80

2 Answers

99 malibu, key won't turn in ignition (it's new cylinder and casing that worked fine before I changed gear shift back to park and connected the battery)


Shake ya sterring wheel from side to side and try turning ya key. The lock could be stuck and needs to be freed up. This should do the trick.

Dec 01, 2012 | 2003 Chevrolet Malibu

1 Answer

2002 Mazda Tribute 6cyl auto gear shift won't click into park so can't remove keys


Check the mechanism inside the gear lever thumb button in case it has failed.

Nov 15, 2012 | 2002 Mazda Tribute

2 Answers

Ignition stuck key won't turn to start car!


Gear shift is not totally in the park position - had the same problem with a 2011 Acura TL - a rubber band kept the gear shift lever from totally seating in the park position.

Oct 02, 2012 | 2003 Ford Focus

2 Answers

2003 crown victoria won't come out of park


Had a similar problem. Solved it two ways first place key in the 3 position move gear to N then start and it will shift easily. Second solution check brake light fuse, it is probably blown replace it and gears will shift OK.

Jul 01, 2012 | 2003 Ford Crown Victoria

2 Answers

Ignition switch won't release key when it is put in park. But when I removed switch and key tumbler, the key tumbler/cylinder releases key. Why won't the key release when it is in park?


Most newer models have a safety feature called
shift interlock. This prevents the key from being turned back
to the lock position if you forget to place the gear selector in park.
Depending on the model,
If it uses a cable, it may be sticking or needs adjusting.
If it uses an electrical solenoid. may be blown fuse or park switch.
Tap, shake, and pull up on the shifter and make sure it's in park.

May 25, 2012 | 1993 Jeep Grand Cherokee

1 Answer

My key wont turn to off in order to remove my key from ignition while in parking


Ignition - Key Stuck In Ignition Switch/Won't Turn Bulletin No.: 06-02-35-005 Date: February 28, 2006 TECHNICAL Subject: Key Stuck in Ignition, Key Will Not Return to Off Position, Shifter Button Won't Release in Park Position (Adjust Shifter Detent Finger) Models: 2002-2005 Chevrolet Monte Carlo Condition Customers may comment on any of the following conditions: - The key is stuck in the ignition cylinder. - They cannot return the key to the off position to remove the key. - The shifter button won't release in the park position. Cause This condition may be caused by the detent finger shifting over time. This may result in mis-alignment and binding of the shift rod on the shift position guide.
WHERE YOUR SHIFTER IS YOU WILL HAVE TO TAKE IT APART ..MAYBE THE RUBBER BOOT IS IT THE WAY,OR THE SHIFT LOCK SELINOID WHENT BAD

Aug 05, 2011 | 2005 Chevrolet Monte Carlo

1 Answer

2005 h2 hummer my car won't shift into park. the key will come out of the ignition


Only suggestion is to put the car into neutruel and use parking brake. You can turn car on and off from this gear. I am not a mechanic nor an export.

Jul 21, 2011 | 1992 Lincoln Town Car

3 Answers

Key gets stuck in ignition


My daughter drives a Suzuki, my solution to her is: while the gear shift lever is in park, lightly put pressure on the gear shift lever, through the park position and while pressing the gear shift towards park light rock left to right while trying to remove the key.

The interlock between the transmission and the ignition switch needs to be adjusted/ repaired or replaced.

Oct 04, 2008 | 2006 Suzuki Forenza

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...