Question about 2002 Ford E350

1 Answer

Just installed a new tps. fault code is gone but idles at 1800 rpm. check engine light does not come on but idle never goes down

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

U may have to adjust the tps can it move from left to right if you losen it ?

Posted on Sep 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why do i have an erratic idle on my 2004 Dodge Durango

Don't need a dash light on, to check for codes
& have some in memory

Have to look at all data & the related modules

Aug 27, 2014 | Cars & Trucks

2 Answers

I have a 2001 Grand Am 2.4 with a low idle problem. It idles at 550 rpm and wants to stall. When I disconnect the battery for a few minutes and then start it again the engine will idle fine at 750 rpm. But...

Does the scan tool power up , can it communicate with the PCM ? It doesn't show NO COMMUNICATION on the tool screen ? Disconnecting the battery resets the PCM back to factory default settings . Driving it the computer relearns fault's or drivers driving habits . What type code reader are you using ?
Do you know how to do automotive electrical circuit testing ? How to test power an grounds for the pcm ? Find a wiring diagram here

ECM Inputs and Outputs Diagnosis

have you check for vacuum leaks ?

Open Circuit Detection Wiring Diagram 1

did you clean throttle plate ?

Apr 02, 2017 | Cars & Trucks

2 Answers

02 Monte Carlo SS 3800 SERIESII V6, no mods. Replaced MAP, IAC, TPS, ECM, Air Filter, Ignition module. No codes! Engine wants to idle from 1500 to 2300 rpm. If I am cruising at 1800 rpm and take my foot...

Sounds like a faulty mass air flow sensor.Try spraying the small thin wires with a nono-chlronated brake cleaner then let it dry for 10-15 minutes then re-install.Make sure to reset the computer whether you clean it or replace it with a new one.

Oct 25, 2012 | Cars & Trucks

1 Answer

Idle surges 1996 Nissan Maxima from 800 to 1800 rpm

could be a dirty throttle body or the idle control motor

Mar 24, 2012 | 1996 Nissan Maxima

1 Answer

Idle is high at start - 1800 rpm. Seems like excessive white smoke from exhaust. Put into reverse and back out of driveway it has a regular shudder (bump bump bump) but not hard metal grinding sound.....

white smoke out of the exhaust would be a sign that it is burning coolant... if it goes away after it warms up, it could just be condensation inside the exhaust pipe. 1800 rpm is a very high idle, maybe have your IAC motor on the throttle body checked... check engine light? if so have the code read at your local auto zone.

Aug 09, 2011 | 1998 Toyota 4Runner

1 Answer

My cars Idle RPM often remains high in the range of 1500 - 2000 and ocassionally Check Engine light comes on, However Check Engine Light dissapear as soon as cars moves on engine power. Did some one has...

a better question is why is idle so high? could be a vaccum leak or other issue. Adjusting the idle circuit is not the answer. Since the check engine light did come on perhaps you can retrieve a trouble code...maybe even a bad tps

Feb 17, 2011 | 2002 Suzuki Esteem

1 Answer

1996 ford bronco 5.8 litre, auto, engine idle has

Do you have a check engine light on? First thing I would do is unplug the IAC motor when the engine is warm. If the idle speed doesn't change you have a vacuum leak or a bad IAC motor. If the idle speed goes down you might have a bad TPS or IAC

May 31, 2010 | 1996 Ford Bronco

1 Answer

Fault codes, p0102,p0122,po507

po102--maf sensor, could be a bad air cleaner and not letting air into engine, po122--tps pedal position sensor low, replace or adjust tps sensor,or wiring,po507--idle control system high input. for this you can take off idle air control, and clean out carbon from were it mounts on engine. it is just before throttle body at end of air intake hose, it is black. do not push on pintle on end of valve when cleaning, use a old toothbrush to clean carbon off of valve, use carb cleaner but do not soak valve in liquid of any kind. good luck!!

Mar 20, 2009 | 1999 Chevrolet Malibu

1 Answer

Honda civic hatchback idles really high

The person that told u that it was the tps and idle air they we're completely right!! The tps sensor is what makes it do that. If you pull the air intake of there's 2 holes on the throttle body. Plug one of the off with your finger while the engine is idling high and it should come down mine was the top hole. If it does go down just get a new tps sensor. and the back sensor on the intake to be safe. or the ghetto way is to plug the hole off, not my sugestion.

Jan 26, 2009 | 1993 Honda Civic 4 Door

Not finding what you are looking for?
2002 Ford E350 Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides