Question about 2002 Ford Mustang

1 Answer

I need to pull ignition cylinder from the steering column

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Take the upper & lower column covers off, under the cylinder there is a button, push in with something thin & pull cylinder out. to reinstall, simply push in. your car may have an access hole without removing covers

Posted on Sep 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to remove ignition cylinder. I have pressed release button on the back, but the cylinder will only come halfway out.


TO REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Key System)
(a) T urn the ignition switch lock cylinder assembly to the
ACC position.
(b) Insert a screwdriver into the hole of the steering column upper with switch bracket assembly. Pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper with switch bracket assembly.
(c ) Insert a screwdriver into the hole of the steering column
upper with switch bracket assembly. Tilt the screwdriver
to disengage the claw of the ignition switch lock cylinder assembly, and pull out the ignition switch lock cylinder assembly.



25656969-ts5vql1j3jwqenesgxdwpnsg-5-0.png Thank you for visiting Fixya.

Apr 20, 2015 | 2010 Toyota Corolla

1 Answer

Where Is the anti theft module


Passive Anti-Theft System (PATS) Transceiver module is around the key lock cylinder behind or under the plastic cover on the upper steering column'
Passive Anti-Theft System (PATS) Transceiver Removal
  1. s4h~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
    Disconnect the battery ground cable, Refer to Section 414-01
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
    2. If equipped, remove the tilt wheel handle.
    3. Remove the upper and lower steering column shrouds.
      1. Remove the screws.
      1. Remove the upper and lower steering column shroud.
      2. Remove the lower instrument panel steering column cover.
        1. Remove the screws.
        1. Remove the lower instrument panel steering column cover.
        2. Remove the instrument panel steering column opening cover reinforcement.
          1. Remove the bolts.
          1. Remove the instrument panel steering column opening cover reinforcement.
          2. Remove the anti-theft transceiver module.
            1. Remove the screw from the bottom of the transceiver module.
            1. NOTE: Only apply pressure or leverage below the key cylinder lower rib.
              Disconnect the electrical connector and remove the module.

Dec 24, 2014 | 2006 Ford Taurus

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

Ignition switch would start but would not lock into position (RUN) and would shut off and then ignition completely locked down and will not move


The ignition key cylinder in a Buick unlocks the ignition and allows the Buick's engine to start. The cylinder contains a switch on the end of it (inside the cylinder) that sends an electric signal to the starter motor. When the ignition key cylinder fails, the Buick won't start. When this happens, you'll need a new ignition cylinder. Purchase replacement cylinders from Buick.
Difficulty: Moderately Easy
Things You'll Need:

  • Ignition key
  • Punch pin
  • Cross-point screwdriver
  1. 1 Remove the screws on the bottom of the steering column on your Buick. These screws hold the steering column cover on. You may need to tilt the steering wheel to its highest position to access these screws.
  2. 2 Turn the ignition key to the "II" position in the ignition cylinder.
  3. 3 Slide the punch pin into the access slot on the bottom of the ignition cylinder.
  4. 4 Push the pin all the way into the access slot while you pull the ignition cylinder out of the steering column.
  5. 5 Insert the new ignition cylinder into the steering column with the key in the "II" position on the cylinder.
  6. 6 Push the cylinder into the column until it "clicks," indicating that it is locked into the column.
  7. 7 Turn the ignition key to the "Off" position.

Dec 15, 2010 | 1995 Buick Riviera

1 Answer

How to change 1999 VW cabrio ignition lock cylinder. How do I get the cylinder out of the aluminum housing?


autozone.com has a free repair guide, see below

printpage_icon.gif


REMOVAL & INSTALLATION

1990-94 Cabriolet,1990-93 Fox, 1990-92 Golf and Jetta


0900c15280267f2b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Lock cylinder drill point.

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel, then remove the steering column covers.
  3. Remove the turn signal and wiper switches.
  4. Disconnect the ignition switch wiring.
  5. On some models, the hole in the lock body for removing the ignition lock cylinder was not drilled by Volkswagen. To make the hole, use the following measurements in conjunction with the illustrations. Drill the hole where "a" and "b" intersect on the lock body. The hole should be drilled 0.19 inch (3mm) deep
  6. Remove the lock cylinder by pushing a small drill bit or piece of wire into the hole and pulling the cylinder out. It might be easier to insert the ignition key, turn it to the right a little and pull on it.

To install:
  1. Insert the lock cylinder into the housing with the key in the cylinder.
  2. While gently turning the key side-to-side, press the cylinder in to the stop. It should click into place.
  3. Temporarily fit the steering wheel onto the splines, then make sure the column locks and unlocks smoothly.
  4. Install the switches, column covers, wiring and the steering wheel.
  5. Connect the battery cable.

1995-99 Cabrio, 1993-99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal.


NOTE Always use a new shear pin when installing the lock cylinder.

Oct 08, 2010 | 1999 Volkswagen Cabrio

1 Answer

Install a Ignition lock cylinder 1997 Pontiac Grand Am


  • Ignition Removal Instructions
  • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
  • Put the key in the steering column lock cylinder set (1).

  • Turn the key to the "START" position.
  • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
  • Turn the steering column lock cylinder set (1) into the "RUN" position.
  • Pull the steering column lock cylinder set (1) out from the lock module assembly.
  • Remove the key from the steering column lock cylinder set (1).

19eb1ff.png


  • Installation Instructions
Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Insert the key into the steering column lock cylinder set (1).
  • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
  • Push the steering column lock cylinder set (1) into the lock module assembly (6).
  • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
  • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
  • Remove the ignition key from the lock cylinder set (1).
  • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

d612a25.png

I hope this helps and good luck.
Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

Nov 02, 2009 | 1997 Pontiac Grand Am

2 Answers

How do you get into the steering column of a 1997 ford tarus to replace key ignition lock


take the plastic cover off the steering column, you will see a small hole at the bottom of the cylinder push in and pull out,thats all you have to do.

Jul 25, 2009 | 1997 Ford Taurus

1 Answer

Ignition switch replacment


Ignition Switch REMOVAL & INSTALLATION The ignition switch is located at the bottom of the ignition key cylinder body. To remove the ignition switch, first remove the ignition lock cylinder.

1993–99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal. NOTE: Always use a new shear pin when installing the lock cylinder.

Jun 25, 2009 | 1998 Volkswagen Jetta

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

1 Answer

Ignition switch


  1. If equipped, disable the SIR system as outlined in . Disconnect the negative battery cable.
  2. Remove the ignition switch trim ring (bezel) by gently prying it out from the lock cylinder with a small suitable prytool.
  3. Remove the trim plate by gently prying around the edges with a small suitable prytool.
  4. Remove the tilt lever (if equipped) by pulling it firmly out from the steering column
  5. Snap off the upper steering column cover by gently prying between it and the bottom cover.
  6. Remove the lower steering column cover screws and lower the steering column cover.
  7. If necessary, remove the instrument panel cluster trim plate.
  8. Remove the two ignition switch bolts.
  9. Detach the two electrical connectors.
  10. Disconnect the ignition lock cable from the ignition switch.
  11. Remove the ignition switch from the vehicle.
To install:
  1. Insert the key into the ignition switch cylinder and rotate it into the RUN position.
  2. Press the cylinder release plunger located at the four o'clock position on the ignition switch.
  3. Use the key in order to pull the cylinder from the ignition switch.
  4. Assemble the cylinder into the ignition switch.
  5. Verify the engagement and operation of the cylinder using the key.
  6. The remainder of installation is the reverse of the removal procedure.
  7. Good luck...

Feb 27, 2009 | 1998 Oldsmobile Cutlass

Not finding what you are looking for?
2002 Ford Mustang Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...