Question about 1995 Ford Mustang

1 Answer

Leaking power steering fluid

I have a 95 Mustang GT that is leaking power steering fluid out the end of the boot on the left side of the steering gear. Do they make a seal kit for this or do you have to replace the steering gear?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 631 Answers

Yes most of the time you can get a seal to replace the one that is there. I am pretty sure the parts stores have one for your steering gear box.

Posted on Sep 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering leaking


Hi Kirk, I'm glad to help!
Kirk, power steering leaks can come from any part of the power steering system. Fluid can leak from seals on the hoses, the hoses themselves, the power steering pump, the power steering gear assembly, usually leaks from the seals at the end of the gear behind the long boots. These are a few things you can check and see what part you need to replace. Hope this helps and have an awesome day Kirk.

Mar 04, 2013 | 2006 Mazda 6 2.3

1 Answer

Is it possible for power steering fluid to get into the engine and mix with the oil? I am loosing fluid and there are no visible leaks, the engine oil and filter was recently changed and now has turne


No, the power steering is entirely a separate and sealed system, wholly external to the engine. The power steering pump pushes the fluid through a high pressure hose into the rack and pinion-the steering gear mounted below and behind the engine-and holds pressure within the rack that enables power assisted steering. At the same end where the power steering fluid hose enters the gear will be a fitting for a return line back to the fluid reservoir. These two hoses are usually routed close together at least part of the way, some may even be held together with brackets. Leaks could develop at the pump, the fluid reservoir, or the two hoses to and from the rack and pinion, or the seals inside the rack and pinion may have failed. You should be able to find the leak-it will only leak to the outside-to check the rack and pinion for leaks, right where your tie rods come out of the gear and go to the wheels for steering, will be a small rubber boot encasing the tie rod and the end of the rack assembly-on both ends is a boot and a tie rod-peel back the rubber boot from the gear ass\'y, it should be dry. If a lot of fluid, the seals in the rack and pinion are gone. It will have to be replaced.
Hopefully you will find a leaking hose or fractured reservoir, but keep looking, air flow may be blowing the leaking fluid back and under the car. Good luck, hope it\'s not the rack and pinion.

Jan 24, 2013 | Honda Cars & Trucks

1 Answer

I power steering leak on a 1989 oldsmobile delta 88 royale 3800 engine the power steering pump is good and less than a year old the fluid is leaking sumwhere underneath the car on the driver side of the...


Pretty old car there, Reginald, (that from a guy who drives a '79 Datsun!)
You'll have to get under there for a close inspection. Raise the car up on jack stands or blocks. Hopefully, a hose fitting may have loosened where it connects to the rack and pinion gear, and only needs tightening. Or a hose may have ruptured and will need replacing. There are two hoses from the pump to the rack, a supply line and a return line. If you see fluid on one, bend it back and forth to look for a break or leak.
The worst case would be a PS fluid seal failure inside the rack and pinion, requiring a new or rebuilt unit. Just paid $240 for a rebuilt unit for a Chrysler last year, to give you an idea.
If the fluid drips from where the rack and pinion steering gear is mounted on a crossmember right behind the engine, peel back the rubber boots on both ends of the rack gear (where your tie rods enter the rack and pinion) and check for fluid there. If a lot of fluid, the seals are bad. In that case, consider a used unit, or a rebuilt, or get used to no power steering. Good luck.

Jan 09, 2013 | Cars & Trucks

2 Answers

How to change inner tie rod ends?


if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------
  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Apr 15, 2009 | 1997 Ford Windstar

3 Answers

Power steering leak on a 1988 full size bronco


The gear box is a common problem on this model. That would be the place I would start. A cheap, temporary fix is to go to your local parts store and ask for Lucas Power Steering Stop-Leak. It will buy you some time.

Apr 09, 2009 | 1988 Ford Bronco

2 Answers

Power Steering system leaking


Have you checked the rack and pinion, if this is leaking you should she fluid on the bellows boot on either side. The seals in the rack start to leak and it will usually show at the black boots (bellows boots) at the inner tie rods. Hope this helps.

You might also want to take a look at the fittings going into the rack and pinion and make sure they are not leaking.

Mar 10, 2009 | 2005 Ford F 350 Super Duty

1 Answer

Power Steering Fluid Leak, boiling fluid.


Look at the steering rack on the side of the car that you think the leak is, look for the steering rack boot or gaiter, it looks like a black circular accordian type thing.
If this is bulging and leaking fluid the seal in the end of the rack is gone, this is one of the most common faults of leaking fluid and at the rate you are losing fluid, the leak is on the pressurised side of the system after the pump (the seal at the end of the rack)

Aug 11, 2008 | 1996 Audi A4

Not finding what you are looking for?
1995 Ford Mustang Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...