a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Sunroof Description and Operation (One Connector System)
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.
Your best bet , take it to a qualified repair shop or buick dealer .
Open up fusebox in the cabin . Remove the 15 amp fuse labelled "ROOM" ( near the bottom). Then check to make sure the relay/ motor wasnt getting any power by clicking all of the sunroof control buttons. Sit for a minute plug the fuse back in, and try the sunroof controls again. First time you click nothing might happen but hold down close and sure enough it should close then.
i have changed the whole sunroof on my mx6,old one was to rusted around edges.if your roof opens but not close it sounds like your motor is dying or your electrical connections to motor are in rough shape.you should be able to close your roof by pushing button and placing your hand in middle of roof and help by lighty pushing/guiding close. be sure roof is straight and not crooked or it will jam and burn out motor
Sounds like sunroof is stuck, motor can't overcome load. Cheap test: car off, interior light turned on try to move sunroof, does light dim? If yes motor is trying to move but can't. If light does not dim then motor not getting power.
first the easy problem is the blower. it has a faulty resistor. it works on 4 because 4 bypasses the resistor to give you full power.
the sunroof sounds like you've got a shorted wire somewhere. the open power wire has to be shorted to a 12v power sorce. there should be a sunroof fuse. check the owners manual for it's location. but if the wire is shorted it may open without it. you may have to remove the headliner to unplug the sunroof motor itself.
hi sounds like a faulty sunroof relay keeping the motor running it may well have blown the fuse or burned the motor out if you connected it back up and it doesn,t work at all but should be able to turn the sunroof back manually look on the sunroof motor there should be sometthing like a slot for a large screwdriver or a bolt head of sorts just wind it back and then check the relays and fuses if your switch is a electronic one make a make shift one and try [simple switch]on and off as this is delicate circiutery and the slightest short can destroy it best of luck yates210456