Question about 1996 Chevrolet Cavalier

1 Answer

95 Cavalier ignition lock system on a tilt column. How do you remove it? The previous owner damaged the whole assy. and I will get one from a junk yard but need to know how to remove the old one. Please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

With covers removed from column there is a square hole on back of lock cyl housing, turn key to run and it will allow you to push in, then pull out lock cyl

Posted on Sep 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacement ignition key 1999 pontiac bonneille


Just the key or the whole lock cylinder with key ?

Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the battery negative cable.
Disable the SIR system. Refer to Disabling the SIR System
Position the steering wheel half way between the upper and lower tilt stops (if necessary).
Remove the steering wheel. Refer to Steering Wheel Replacement .
Roll back the shift lever seal from the upper and the lower shrouds.
Remove the tilt wheel lever (if necessary). Refer to Tilt Lever Replacement - On Vehicle .
Remove the 2 TORX® screws from the lower steering column shroud.
Remove the lower steering column shroud.
Remove the 2 TORX® screws from the upper steering column shroud.
Lift the upper steering column shroud to gain access to the lock cylinder access hole.
Using a bent tip awl, insert the tip into the ignition lock cylinder access hole.
Turn the ignition lock cylinder to the START position.
Using the bent tip awl, push down on the ignition lock cylinder retaining pin.
Release the ignition lock cylinder to the RUN position.

Remove the ignition lock cylinder from the lock module assembly by pulling the ignition lock cylinder away from the steering column.

There may be a video on youtube .

Feb 23, 2017 | Pontiac Cars & Trucks

1 Answer

How do i remove the ignition lock ccylinde on a 2002 buick lasaber


Removal Procedure
Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:
• Air bag deployment
• Personal injury
• Unnecessary SIR system repairs
In order to avoid the above conditions, observe the following guidelines:
• Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
• If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.
Disable the SIR system. Refer to Disabling the SIR System in SIR.
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Position the steering wheel half way between the upper and lower tilt stops, if necessary.
Remove the steering wheel. Refer to Steering Wheel Replacement .
Remove the tilt lever. Refer to Tilt Lever Replacement - On Vehicle .

Remove the lower steering column trim cover retaining screws.
Remove the lower steering column trim cover.

Remove the upper steering column trim cover retaining screws (3).
Buick Ignition Lock Cylinder Replacement

Nov 09, 2016 | Buick Cars & Trucks

1 Answer

Where Is the anti theft module


Passive Anti-Theft System (PATS) Transceiver module is around the key lock cylinder behind or under the plastic cover on the upper steering column'
Passive Anti-Theft System (PATS) Transceiver Removal
  1. s4h~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
    Disconnect the battery ground cable, Refer to Section 414-01
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
    2. If equipped, remove the tilt wheel handle.
    3. Remove the upper and lower steering column shrouds.
      1. Remove the screws.
      1. Remove the upper and lower steering column shroud.
      2. Remove the lower instrument panel steering column cover.
        1. Remove the screws.
        1. Remove the lower instrument panel steering column cover.
        2. Remove the instrument panel steering column opening cover reinforcement.
          1. Remove the bolts.
          1. Remove the instrument panel steering column opening cover reinforcement.
          2. Remove the anti-theft transceiver module.
            1. Remove the screw from the bottom of the transceiver module.
            1. NOTE: Only apply pressure or leverage below the key cylinder lower rib.
              Disconnect the electrical connector and remove the module.

Dec 24, 2014 | 2006 Ford Taurus

2 Answers

How do i change out the ignition switch?


Ign Systems 8D - 19 Service manual '92 Dak
Disconnect neg battery cable Tilt column:Remove tilt lever (counterclockwise) Remove upper and lower covers (3 screws) Remove ign switch mounting screws (3) with torx bit Gently pull switch away from column Release two connector locks on the seven-terminal wiring connector. Remove connector from ign switch Release connector lock on the Key-in-switch and Halo Light four terminal connector. Remove connector from switch Remove key cylinder from switch as follows: With key inserted and ign switch in the LOCK position use small screwdriver to depress the key cylinder retaining pin flush w/ key cylinder surface Rotate the key clockwise to the OFF position The key cylinder should now be unseated from the ign switch assembly With key cylinder in unseated position (key cylinder bezel about 1/8 inch above ign switch halo light ring) Rotate key counterclockwise to LOCK position and remove key Remove key cylinder INSTALLATION; Install electrical connectors to switch making sure locking tabs are fully seated into connector Mount ign switch to column Shifter must be in PARK position Park-lock dowel pin on ign assy must engage with park-lock slider linkageVerify ign switch is in lock position (flag is parallel w/ ign switch terminals..off to the right) Apply dab of grease to flag and pin Position park-lock link and slider to mid-travel Position ign switch against lock housing face Be sure pin is inserted into park-lock link contour slot Tighten screws Assemble cover Tighten more screws Tilt column and install tilt lever (clockwise) instsall neg battery cable Gently insert key cylinder into ign switch asssy until it bottoms Insert key and gently push key (inward) and rotate clockwise to end of travel Rejoice in how much money you just saved yourself

Jun 16, 2014 | 1992 Dodge Dakota

1 Answer

How do I change the ignition switch in my 93 plymouth van?


FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Sep 18, 2010 | 1993 Plymouth Voyager

3 Answers

How to remove and install ignition switch


remove the steering coloum trim. Turn the key to run position, Press locking button on back of steering coloum housing assembly, Remove lock cylinder, Disconnect the ground strap from lock preload spring ( if equiped ) . Make sure key is still in run position when you reinstall.

If the key is non functional and you cannot turn to run then you will need the tool in this picture197ca25.gif

Aug 12, 2010 | 1997 Chevrolet Cavalier

1 Answer

How do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota


CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:
  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Jul 30, 2010 | 1993 Dodge Dakota

2 Answers

Diagram on to change turn signal arm on 1994 chevy cavalier , do u have to pull the sterring wheel


1991-94 Cavalier
See Figure 5
This procedure covers removal and installation of the headlamp, headlamp dimmer switch, turn signal and hazard switches, as well as the cruise control switch.
  1. If equipped, disable the SIR system. For details, please refer to the procedure located in of this repair guide.



0900c1528003bf08.jpg enlarge_icon.gif enlarge_tooltip.gif Fig. Fig. 5: View of the steering column showing the turn signal switch location
  1. If not already done, disconnect the negative battery cable.
  2. Unfasten the horn pad, then remove the steering wheel. For details, please refer to the procedure earlier in this section.

If necessary, using locking pliers with a piece of rubber (such as a spark plug boot) between the jaws to help prevent damage to the tilt lever during removal.
  1. If equipped, remove the tilt lever from the steering column by grasping the lever firmly and twisting counterclockwise, while pulling it from the column.
  2. Remove the upper and lower steering column covers.
  3. Remove the dampener assembly, then unfasten and remove the switch assembly from the vehicle.

To install:
  1. Position and secure the switch assembly.
  2. Install the dampener and the upper and lower steering column covers.
  3. If equipped, attach the tilt lever to the column.
  4. Install the steering wheel, then fasten the horn pad.
  5. If equipped, enable the SIR system, as outlined in of this repair guide.
  6. Connect the negative battery cable.

Nov 15, 2009 | 1994 Chevrolet Cavalier

1 Answer

How do you replace the ignition switch for 1996 chevrolet cavalier?


Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding

  • Disable the airbag system
  • Remove the tilt lever if equipped
  • Remove the upper and lower steering column covers
Ignition Switch

  • Remove the ignition switch retaining screws
  • Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors
Key Lock Cylinder

  • Turn the key to the run postion
  • Depress the lock button and remove the key lock cylinder

Nov 02, 2009 | 1997 Chevrolet Cavalier

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
1996 Chevrolet Cavalier Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...