Question about 2004 Jaguar S Type

2 Answers

Reverse sensors go constantly when in reverse

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Expert
  • 322 Answers

This can be caused by dirt build up in the air gap in one of the sensors. carefully clean around the sensors with a tooth brush and water
DO NOT JET WASH! If this does not work check the connections to the module found in the bottom LHD Side of the boot, sometimes the plug connections are affected by water/damp. I had the same problem - pulled the plug off - remade it and sprayed with silicon spray to keep away damp - and its been no trouble since. If non of this works you may have a faulty sensor or unit.
Hope this helps - good luck.

Posted on Nov 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a faulty revevse sensor , A comment was made that if i took one of the wires off the faulty one, from the senser box The others would work.
Were is the box located in the boot,
I have a jaguar 2000 model S-type V6.
Thanks
Lou.

Posted on Sep 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ford focus zetec reverse sensor comes on when i turn on the ignition. It stays on constant while i am driveing not beeping just a constant drone


It sounds like one of the sensors mounted in your bumper is bad or you have something obstructing one of them, mud, snow, etc.

unplug them one at a time until the noise stops, that will be the defective one

Feb 16, 2017 | Ford Focus Cars & Trucks

1 Answer

Reversing beeper has constant beep


The easiest possibility is that the proximity sensor thinks something is constantly very close to your bumper. Assuming you don't have any weird stuff hanging off your car that could confuse it, the sensor is likely damaged.

Oct 20, 2014 | 2008 Toyota Camry

1 Answer

Reversing sensors on my 05 Sportage beep constantly when in reverse. I have cleaned sensors but it still happens. What could it be


I am not sure what noise you have. it sounds like its either a reverse alarm which sounds when you are backing up. that's what it is supposed to do. If it is an alarm... it may be telling you that you have a reverse light out.

Sep 28, 2014 | 2005 Kia Sportage

1 Answer

Nissan tiida reverse sensor problems


clean off the sensors on the bumper

Apr 17, 2013 | Cars & Trucks

1 Answer

Reverse censors are on constantly when in reverse.


One of your rear sensors ( 4 of them located on the back bumper) has most likely failed or was damaged. Check the back sensors for any visual damage (they are about the size of a nickle) and panted to match the rear bumpers paint.

Good Luck!

Nov 26, 2010 | 2003 Jaguar S-Type

2 Answers

Sensor beeping continously in reverse


Try to clean rear parking sensors. Check also electric cables and connections, clean if necessary. Commons faults are sensors out of order. If one or more sensors faults you hear only a continous constant noise when you put in "R" gear. You need a VAS, VAG-COM, Bosch KTS, ... diagnosis scantool. The factory parking system will be scaned from errors with this instrument, and you will find exactly which sensors are out of order (for example: rear left center sensor, rear right side sensor break off, short to ground or short to plus).

Mar 28, 2010 | 2003 Volkswagen Passat

2 Answers

My 2003 Jaguar S-Type has a faulty Reverse Park Control system. When shifting into Reverse gear, a constant tone sounds until the gear is shifted into a forward gear or neutral. What are the usual causes...


This is a sensor fault. The easiest way to locate wich sensor is faulty is to get up close to the sensors when the car is in reverse gear (engine off) with the ignition on and put your thumb nail on the sensor face as this will amplify the ticking noise that can be heard from the sensors. No tick indicates a sensor fault.

To disconnect the system will just give you the same problem with the constant tone unless you disconnect the park aid module wich is located in the boot of the vehicle on the left hand side behind the carpet trim. Beware that the handbrake module is there so ensure that you are looking at the right module (it will say on it)

Sensors are not expensive unless you need to have them painted to body coulor as they come in black. Easy push in/out fitment from the behind the bumper. Corner sensors can be replaced with the bumper in situ but centre sensors require the bumper to be removed.

Hope that helps

Feb 28, 2010 | 2003 Jaguar S-Type

Not finding what you are looking for?
Cars & Trucks Logo

597 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78936 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...