Question about 1994 Dodge Intrepid

1 Answer

We have changed the crank shaft sensor and the cam shaft sensor and plugs and cadlac convertor and fuel pump and our car still misses real bad every now and then it might straight out for few min you have to hold gas to keep it runnung would this problem be associted with a coil pack

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Well, it sounds more like a timing belt issue than a coil pack. When you have gas applied and the engine running a little higher than idle RPM it seems fine because the belt is under tension and holding the timing when you back off the gas the belt gets loose and it runs like it is out of time. If it runs fine at first and starts acting up when it gets warm it could be the coil pack but I would check the timing and see if it is erradict when idling to make sure you don't have a timing belt issue. If that breaks while you are driving you will have to repair the head as well as replace the timing belt.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is Mazda Miata stumbling and missing after reaching closed loop?


Check compression. After spark and fuel, compression is next on older cars.

Jul 18, 2015 | 2000 Mazda MX-5 Miata

1 Answer

2004 Nissan Sentra SE-R Cranks but won't start!


It could be the fuel system.
It could either flooding or starving for fuel.
If injectors are fouled badly it will wet the plugs and not fire.
If plugs are pitted that makes it easier to flood. (check plug tip condition, check all plug wires and boots are good)

If it is starving -- fuel pump weak (going to fail).
Need to test fuel pump pressure.

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

Why would my1999 s10 start missing out going down the road ?


Check fuel pressure to see if a fueling problem. Some stores rent or loan fuel pressure gauges. Check for possible trouble codes that may indicate a problem.

Gas, air, spark, and compression- one of them is wrong or missing for the engine to misfire.

Aug 30, 2014 | 1999 Chevrolet S-10 Pickup

2 Answers

Car stopped running while driving


run the fault codes and check for cam/crank position sensor . check that the cam shaft is turning (broken cam belt)

Jan 17, 2014 | Volkswagen GTI Cars & Trucks

1 Answer

Will not take fuel or run over 2000 rpms bucks and revs up & down


check your coils, plugs & wires and fuel filter. if all are good check the fuel pump pressure

Dec 25, 2013 | 2004 Dodge Neon

1 Answer

2001 crankshaft sensor changed now car want start


If the store pulled the codes and it had a code for the crank sensor, the real problem could be a bad cam sensor or a problem with the crankshaft. The crank sensor "sees" a mark or magnet on the crank and sends a signal to the computer. The computer takes that signal and compares it to the cam sensor to start the engine then runs off of one or the other. It sounds like the computer is not seeing the two signals match up.

Jun 24, 2012 | 2001 Chevrolet Cavalier

1 Answer

Runs fine then starts missing real bad then runs fine again. changed fuel pump and filter, plugs, plug wires, and distributor and still no luck


check the ignition coil, crank position sensor, and any wiring. that check engine light should be glowing though when it misses...

Feb 27, 2011 | 1996 Jeep Cherokee Country

1 Answer

99 Jeep Cherokee Sport, 4.0L -won't start


you need to have it connected to an OBD2 machine and watch if you are missing the cam sensor showing RPMs
or if your missing crank sensors RPMs,
it could be a wiring problem or computer if your seeing the RPMs from both sensors,and the last thing i would check is hooking up a fuel gauge to the reed valve and watch what fuel pressure you have while cranking,if the cam sensor is the culprit it will turn the fuel off after the cranking.

Jan 11, 2010 | 1999 Jeep Cherokee

2 Answers

Has a code 0174 and 300 code checked intake gasket that was good replaced fuel pump to low of pressure took on highway ran fine but somtimes has miss on right side mostly 4 and 6


could be many things cam sensor crank sensor fuel injectors or the coil could be the issue if its a multi port fuel injected system.

Jul 18, 2009 | 2005 Chevrolet Tahoe

Not finding what you are looking for?
1994 Dodge Intrepid Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...