Question about 2004 GMC Yukon

2 Answers

2007 Yukon tail stop lights wont light up

2007 Yukon tail stop lights don't come on when braking. Fuses and light bulb have been replaced. the lights still don't come on. Emergency lights and turn signal lights still work what seems to be the problem can it be the brake switch / were is it locate?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

It sounds like the brake switch, that is usually located along the shaft of the brake peddle under the dash, these sometimes are in a bracket for ajustment may not be able to depress switch. Falow starting at peddle go up to dash, you should be able to see it. Hope this helps.

Posted on Sep 08, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

The switch is located on the brake peddle lever towards the top .It is held on with a clip ,This could be the problem :)

Posted on Sep 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights don't work but 3rd stopping light does


it should be easy, first check all the fuses, if that dont work remove the tail lights and check the wiring it may have broken wires or blown bulbs

Jul 18, 2012 | 2003 Chevrolet Impala

2 Answers

Driver side brake light is not working. Replaced bulb, but didn't need to it is the same bulb that works the tail lights, which still worked. Ugh, 2006 jeep liberty. Someone said it was a brake...


THAT RIGHT IF BRAKE SWITCH BAD NO BRAKE LIGHT WILL WORK.SPRAY ELECTRICAL CLEANER IN BULB SOCKET BULB SOCKET COULD HAVE OXIDATION AND CORROSSION CAUSING POOR CONTACT.

Sep 12, 2011 | 2006 Jeep Liberty

1 Answer

What could be wrong with rear brake lights on 2007 Trailblazer if fuses in rear seat compartment are OK and tail light bulbs are OK?


Remove the tail lamp housing and test for power at the wiring connector. Does the center high mount stop lamp operate correctly? The lamp circuit boards have seen many problems.

Feb 24, 2010 | 2007 Chevrolet TrailBlazer SS

1 Answer

Brake lights ,tail lights wont work i have replaced fuses,bulbs


Check fuses, I believe that the WJ's (99-04) ran a separate circuit for bake lights. Not sure if they did same for the ZJ's (93-98)

Oct 02, 2009 | 1998 Jeep Grand Cherokee

2 Answers

Brake lights wont work replaced switch checked fuses


Replace bulbs, clean sockets, check towing harness, check brake swich under brake pedal. fuses???
Vitally

Sep 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Tail light out but break light works on a 2000 yukon


Depend cause you got a running light and another one thats a running like along with brake light.If its the one that has the brake light and the light comes on when you brake and not when you turn on the headlights then you have a bad bulb .Replace that bulb and your set.good luck

May 27, 2009 | 2000 GMC Yukon

2 Answers

Right brake light out; tail light works fine


most rear tail lights and turn/stop lights are the same dual filiment bulb. it is possible for your tail light to work and your brake light not to and still have a bad bulb. I would check the bulb first, your brake light works on the left yes? this would mean that the fuse is fine

Mar 31, 2009 | 2006 Dodge Stratus

1 Answer

Brake lights dont work untill i turn the lights on, then stay on


Hi, are the tail lights and the brake lights in the same light unit?
If so, there is a possibility the bulbs are in the wrong way. If it is a stop/tail bulb then there are two locating pegs on the side of the metal part. If you look, one is higher than the other which has to locate into the correct slot in the holder.

Another possibility is the bulb is wrong, there are double and single contacts. Check the contact on the base of the bulb is the same as the contacts in the holder.

TL

Feb 09, 2009 | 1999 GMC Yukon

2 Answers

No brake lights, fuses keep blowing and wont shift out of park


I would look for a wiring short in the trunk at the taillamp area, or, inspect the sockets for the taillamp bulbs for corrosion. In any case, you have a short circuit in the trunk area, also check the wire that comes from the body & goes up the trunk hinge on the driver side; that wire may be chafed, and it may be shorting out. Hope this helps; please get back to me if you need any further assistance.

Nov 04, 2008 | 1996 Toyota Corolla

Not finding what you are looking for?
2004 GMC Yukon Logo

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...