Question about 2000 Jeep Wrangler

1 Answer

Spline shaft is wraped coming out of transfer case.

Posted by on

  • Wayne Holden May 11, 2010

    Put in a new one. Ok, what do you want to know?

  • vtrktrmn May 11, 2010

    What is the question? It sounds like it has twisted. if it has it will have to be replaced.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 986 Answers

We need more info. Have you lifted it? after market drive shaft? The more info the more we can help

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge ram 4 wheel drive noise


check the front drive shaft spline or "U" joint at the transfer case
splines on this shaft wear more quickly that the rear drive line
as the operation angles for the front diff are more acute that the rear shaft

Dec 31, 2016 | Dodge Cars & Trucks

1 Answer

I cant remove the metal end and spline inside of my kia sedona


Try to get a pry bar or large screwdriver between the CV housing and the transmission case. A little force may be required, but you have to pop the housing out of the transmission. A c-clip in a groove on the splined shaft is holding the shaft in, and must be popped outward, for the housing and shaft to be removed.

Nov 25, 2013 | 2003 Kia Sedona

1 Answer

1999 Dodge Durango 4x4 with bad transfer case?


from what you said, it sounds like the converter on the transmission may have broken, Since it's loosing oil, it shouldn't be difficult to determine which part is leaking.
Check the transmission and transfer case fluid. Whichever is low is the unit with the problem. To verify, re-fill it and put a pan under there and start it up and look. You mentioned the yoke and spline. If either have broken you need to determine why, then replace whatever is necessary. If the splined shaft that the yoke is attached to has broken then the transfer case will need to come apart as it is part of the larger internal assembly. (may be easier for you to just get a different unit from a scrapyard.)

Jun 02, 2010 | 1999 Dodge Durango

1 Answer

Tried removing the front drive shaft from transfer case. It won't come off, could there be something holding it from inside the transfer case?


Unbolt it from the front diff and then pull it out of the front of the transfer case. There will be a small snap ring inside that will offer up resistance, but it does slide out with some help, use your pry bar between the shield and the t-case to "pop" the spline past the snap ring inside. the first one i did i was kinda leary of prying on this too, but it was what was required just pull on the front drive shaft with one hand, and pry behind the shield with the other it'll feel like it's not going anywhere, but watch out, it'll just "pop" and be out. Be careful!! Good Luck!

Mar 09, 2010 | 2005 Chevrolet Silverado

1 Answer

Where are the splines on a steering column


splines on any shaft are used where two parts are joined together ie: your steering wheel is joined to the shaft by way of a spline. (serrated part of shaft that matches serrated receiver hole). In some cases there is no spline, but a flat is added instead which serves the same purpose of keeping the shaft from turning without turning the shaft it is attached to.
Some lower shaft joints can be either splined or use a flat. Be aware that some splines have a "locator" spline which essentially one fat spline that aligns with a wide spline groove in the receiver hole.
Most splines have a locking collar on them or a cross bolt that helps keep them together, except for the steering wheel that uses a nut on the top of the shaft.
Confused yet? Hope not!!!
Good luck!

Sep 25, 2009 | 1989 Jeep Cherokee

1 Answer

4X4 Ranger transmission to tranny case problems


replaace transfer case or more head aches

May 26, 2009 | 1984 Ford Ranger

1 Answer

4X4 Ranger transmission to tranny case problems


nissan maxima 1987

no spark at all have tried a few basic things still nothing.

May 26, 2009 | 1997 Chevrolet C1500

3 Answers

Transfer case wont work


might want to make shure the shifter linkage arm is in gear. if the linkage is bent at all it will hold the trans inbetween gears not allowing the motor to spin the drive shaft

Jan 25, 2009 | 1989 Jeep Cherokee

1 Answer

4x4 Problems


sorry lost here ,never seen one but if transmission shaft is turning to front diff then the problem is their,could be anyting from a sheared diff pinion to a broken planet wheel or possible evan a snapped half shaft or the spline on the end of the half shaft has worn and rounded off

Oct 07, 2008 | 1999 GMC Jimmy

Not finding what you are looking for?
2000 Jeep Wrangler Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...