Question about 2003 Volvo S40

1 Answer

How do you change the rear side marker lights?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

If you mean replace burned bulbs, find the marker light and locate the wires on the back. Get a good hold on the plug and turn in 45 to 90 degrees and then pull out, replace the bulb and re-install.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello i have a toyota camry 1992 and my passenger side marker wont turn off ???


That's very odd, because the wiring for all of the side markers are just splices from the nearest park lamp wires- the rear tail light in the rear (and the license plate lamps are also splices from these tail lights), and in the front side markers, they are splices from the nearest park lamps. Do all the other park lights work and turn on with the park light switch on? I would examine the 2 wires from that side marker's socket to the wiring harness it goes into-the power wire would somewhere splice into the passenger tail light wire. The other wire would be a ground wire and also splices into a ground wire for the rear end. To be on, the marker lamp would have to be getting power from some live source. I can't imagine where. Does the rear passenger light work correctly?

In that harness to the rear where the park lamps run, there might be a live wire going to an electrical trunk latch switch, or maybe a trunk lamp. If the wires were frayed right beside the side marker wire, you could have some cross feeding of power between the two. Let me know, we always appreciate feedback.

Sep 06, 2015 | Toyota Cars & Trucks

1 Answer

When pressing the lock or unlock on the keyless entry are the front side marker lights suppose to flash along with the mirror and rear lights.


go into the radio and change it there. If they work when it is running then the radio
is where you look

Apr 13, 2015 | Cars & Trucks

1 Answer

Replace rear side marker light


I had this message sent to me to solve....THIS IS MY QUESTION THAT I ASKED....LOL....SINCE THEN; I'VE BEEN INFORMED THAT YOU HAVE TO GO THROUGH THE OUTSIDE TAIL-LIGHTS TO GET TO THE MARKERS
DOES ANYONE ELSE KNOW ANOTHER WAY?
I have stainless steel covers over my tail-lights and will have to remove the "adhesive" on the covers to remove the tail-lights...HELP!

Jul 05, 2014 | 2007 Chevrolet Corvette Convertible

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

How do I change the front side marker light bulbs?


Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    Replace side marker light on lexus rx300


    Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

    Jul 25, 2009 | 2000 Lexus RX 300

    1 Answer

    Had a problem with a right, amber side marker on right side


    Usually one of the holes in the marker light where screw goes in, has metal contact where screw meets light, but if not, and they are not push in wire connection type from behind, then just run your white wire up through hole in housing, and bare the end & tighten it up under screw holding light to body. White should be ground, brown should be power.

    Jul 02, 2009 | 2004 Dodge Ram 2500

    1 Answer

    2004 VW Passat front marker light bulb


    Push in on the rear side of the light and slide the whole assembly to the rear.

    it is hard to do.

    Jun 07, 2009 | 2004 Volkswagen Passat

    Not finding what you are looking for?
    2003 Volvo S40 Logo

    439 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volvo Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8514 Answers

    Are you a Volvo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...