Question about 2003 Mazda Mazda6

Open Question

2003 Mazda 6 - no air flow from vents

I have a 2003 Mazda 6 and when I turn the air conditioning on, I don't get much air flow. The actual air coming out is cool to the touch, there just doesn't seem to be any pressure (flow).

Posted by on

  • Ed 4 ward May 11, 2010

    do you have automatic temp settings or is it manual temp settings?



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Does 2004 Mazda MPV ES equip with a cabin air filter?

(cabin filter solution) Their is an cabin airfiliter behind the glove compartment (2004 mazda mpv) which is very easy to take off. Replace the airfilter or clean it with soap and water. Open the glove box and on the bottom left had side of the glove box if you apply enough presure on it by pulling it out towards you and slightly down it should pop off. The right side should slide out immediately following the left side pop. All it is, is a fork like claw holding on to a bar. On the ride side is a bar sliding into a hole. That should do the trick. After the first time its a sinch.

Posted on Feb 10, 2009

  • 1 Answer

SOURCE: Cold Air Intake - Mass Air Flow Sensor Adapter

i have a 91 mx6. the intake is all cattywompus and im just goin to take a piece of metal and tube and cut a hole in the peice of metal and weld the tube to it take my stupid box out and run that pipe staight to a coupling and then to the cone air filter. BAM!!!! problem fixed... i maight be able to fix yours too... e-mail me k?

Posted on Apr 16, 2009

  • 22 Answers

SOURCE: Loud acceleration noise in my 2003 Mazda 6 2.0 auto

one thing to check is rear engine mounting i have had a stone wedged in one and it causes a nasty noise when accelerating

Posted on Apr 17, 2009

  • 66 Answers

SOURCE: 2002 mazda millenia mass air flow sensor

Look in the oulet air cleaner tube, it's hold by 4 nuts.

Posted on Sep 16, 2009

Testimonial: "Thank you so very much for your assistance. I wish i could ask you alot of other questions!!"

  • 97 Answers

SOURCE: where is the oil pressure switch on a 2003 mazda 6

Hope this helps, kinda a crudy picture but it's the best i could come up with.bf99aec.gif

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

When trying to use A/C or heat,the air is barely coming out the vent but the blower motor is working. What could it be?

Flow though the panel registers (not vents) and floor/defog outlets can be impeded by clogging of the (actual) vents in the doors because air can only enter the cab as rapidly as it can be vented from the cab to the exterior. Find those vents and make sure they are unblocked and free of clogging material buildup. As a quick check for fault cab venting, crack open a window to see if register air flow speed comes up to match fan speed. If not, then something is blocking the door vents; possibly even ice.

Mar 16, 2015 | 2003 Dodge Ram Pickup 1500

1 Answer

2003 Chevy trailblazer, the 4 front dash air

{: ) Check first the fuse labeled HVAC1 10A at the rear fuseblock. If okay, the mode actuator could be faulty. You can try this: turn ignition switch and a/c off for a minute. Then turn ignition on, wait forty seconds. Afterwards, start the engine, and check your a/c again.

Aug 01, 2010 | 2006 Chevrolet Trailblazer

1 Answer

This car has been wrecked, so my problem is that the air condition flow feels like it is escaping somewhere. The air is cold and it comes out of 2 vents but the other 2 is barely blowing? Summer is upon us...

Sounds like if you take the under dash cover off and look up in there you'll seee the problem. a duct hose or tube has come off or is broken or missing. Hopefully by turning it on while looking and feeling around you can find the end that came off and just snap it backtogether.

May 21, 2010 | 2003 Mazda Mazda6

1 Answer

My 2003 Mazda 6 has a very strong petrol smell coming out of the petrol cap hatch area. I've replaced the petrol cap with a new one and also had the car checked by a mechanic to make sure the tank has no...

Well you mechanic has obviously not done his job , on some cars there is a vent tube that runs ajacent to the main filler tube there may be a breach in the rubber hose or where it connects, but more than likely the purge canister located in the engine compartment is faulty not allowing the gas tank to vent, have the purge canister checked.

Dec 07, 2009 | 2003 Mazda Mazda6

1 Answer

No air flow through the rear vents with ac or heat on high

make sure the control knob on the dash is on "RR". This lets the driver control all the vents in the back. The heat only comes out of the floor vents, if you have the knob on the blue dots that represents the air conditioning in which the cool air will come out of the vents up above in the back. There is also an area on the control knob on the dash where you can turn the knob to shut the heat and air conditioning off. If the knob is in this position then you can control everything with the knob up above the seat right behind the driver's seat.

Jan 15, 2009 | 2004 Honda Odyssey

1 Answer

2004 Ford Crown Victoria no air flow through main air vents

Chances are the electronic/digital HVAC control unit is bad. This same problem happened to me and I had to replace the entire unit. The dealer wanted to charge $800 for just the part! After I freaked out on them, they found a used one for less than half. Sorry, but there's no easy fix here.

Jun 26, 2008 | 2004 Ford Crown Victoria

4 Answers

Air conditioning and heating

The vacuum line on the drivers side of the intake manifold just below the throttle body fell off.

May 26, 2008 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Mazda Mazda6 Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides