Question about 2000 Chrysler 300M

1 Answer

Headlamp bulbs for exchange chrysler 300M -00

Headlamp bulbs for exchang. Do I need to unplug the front bumper.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

If you're just changing the bulbs, then all you need to do is reach behind the top cover and then remove the cover off the back of the headlamp assembly

Posted on Sep 08, 2009

Testimonial: "Now is the new bulbs in place. Thanks."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Chnage turn signal bulb


300M? Front? Crawl under the front bumper and follow the wires. Turn the socket- nothe the wires counterclockwise until the socket releases from the back of the bezel. Gently pull the old bulb out, replace. reinstall in reverse of dis assembly. REAR? Open the trunk, peel back the carpet to display the plastic nuts holding the tail light assy in. Release the assembly and pull it off the fender. Turn each socket counterclockwise until the socket releases from the back of the bezel. Gently pull the bulb out of the socket. Re assemble in reverse of dis assembly.

Dec 17, 2011 | 2000 Chrysler 300M

1 Answer

1996 sierra 1500 truck passenger lowbeam headlight bulb exchange?


there is to tabs right behinde the headlamp you pull up an can remoce headlight to replace bulb easier. then just twist bulb out an make sure not to touch the new bulb with your fingers. but if your have what they call a sealed beam then there is 4 screws in front of headlight that hold it in.

Jan 05, 2011 | 1996 GMC Sierra

1 Answer

How to change headlight lamp in 2005 Pontiac g6


To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Dec 25, 2010 | Pontiac G6 Cars & Trucks

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How to replace a headlight bulb in chrysler 300


    you will need to unbolt bumper cover and pull out on side light is being replaced, doesnt have to come of completely but needs to pull back to get light out,remove the bolts from the top hold light asm, in, then remove top cross plate that holds hood latch and put to the side, then remove bolts and clips holding bumper cover and pull cover foward until you have room to pull light out, then remove the bulb from the rear,this bulbs are 90 degree plug type not the straight one, they dont fit, hope this helps, not bad to do, just sounds so.

    Jun 09, 2010 | 2000 Chrysler 300M

    1 Answer

    How do you remove the air filter box on a 2001


    REMOVAL
    Release hood latch and open hood.
    Access Rubber Grommet
    Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
    Fastener Locations

    Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
    Remove Push In Fasteners
    Remove the push pins attaching the fascia to the upper radiator closure panel.
    Headlamp Jack screws

    Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
    Roll Fascia Forward

    Roll fascia forward to clear way for headlamp housing removal.
    Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    Remove Headlamp Housing

    INSTALLATION
    CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    Place headlamp housing into position.
    Connect wire connector to lamp socket(s)
    Verify headlamp and signal lamp operation.
    Install jackscrews to attach headlamp housing to crossmember.
    Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    Install nut on fascia stud through the splash shield access hole.
    Verify headlamp operation and alignment


    Nov 03, 2009 | 2001 Chrysler 300M

    1 Answer

    I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


    The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
    1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
    2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
    3. You will also need to remove some of the fasteners at the front of the inner wheel well.
    4. The Front Bumper Fascia is the plastic cover over your front bumper.
    5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

    Oct 27, 2009 | 2008 Chevrolet Malibu

    1 Answer

    2005 crysler town and country


    COOLING FAN RELAY IS LOCATED ON FRONT BUMPER SUPPORT..REMOVE LEFT SIDE HEADLAMP ASSEMBLY,AND SOME SCREWS IN UPPER PART OF BUMPER COVER..RELAY IS RIVETED TO SUPPORT..DRILL OUT RIVETS AND UNPLUG RELAY..NEW RELAY MAY COME WITH NEW RIVETS OR SCREWS TO MOUNT IT

    Jul 11, 2009 | 2005 Chrysler Town & Country

    1 Answer

    How do you replace headlamp bulbs on 1999 chrysler 300


    You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
    Tell me if this works for you?
    HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
    REMOVAL
    1. Release hood latch and open hood.
    2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    8. Remove headlamp housing Remove Headlamp Housing
    INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
    1. Place headlamp housing into position.
    2. Connect wire connector to lamp socket(s) and/or bulbs.
    3. Verify headlamp and signal lamp operation.
    4. Install jackscrews to attach headlamp housing to crossmember.
    5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    7. Install nut on fascia stud through the splash shield access hole.
    8. Verify headlamp operation and alignment

    Mar 27, 2009 | 1999 Chrysler 300M

    Not finding what you are looking for?
    2000 Chrysler 300M Logo

    186 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8270 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...