Question about 1989 Chevrolet K1500

1 Answer

How to install a clutch slave in 89 chevey pickup

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Make sure pushrod of slave is well seated in fork slot,bolt it,then bleed slave.

Posted on Sep 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 s 10 clutch wont catch after bleeding it replaced masre and slave clutch


Are you sure all the air is out of the system and you have a firm pedal feel. If not have a shop pressure bleed the clutch hydraulic system.

Apr 21, 2016 | Cars & Trucks

1 Answer

1989 chevey s10 blazer hard time shifting into gears


The problem and the solution is clutch master cylinder and a slave cylinder

Mar 28, 2012 | Cars & Trucks

1 Answer

The clutch will not engage properly on my 1988 toyota pickup. Already replace clutch master cyclinder and clutch slave?


There are a couple of possibilities; worn clutch plate, failed pressure plate, possible hanging up of the throw-out bearing. Also, some hydraulic clutches have a throw adjustment on the slave cylinder that may need adjustment after replacing the slave cylinder.
If you plan on more DIY maintenance, I would highly recommend buying a Haynes service manual, you'll find the $25 well-spent:
Toyota pickup manual

Mar 31, 2011 | 1988 Toyota Pickup

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

I have a 89 toyota pickup 4 speed. When I'm stopped at a stop light, and let out on the clutch it seems like it has lost pressure. When I'm shifting down the road it shifts fine. I checked the fluid and it...


this sounds like the clutch slave is goin out, this unit is on the outside of the transmission. Possibly losing pressure!! Your transmission does not use transmission fluid, but instead gear oil. Have the following checked:
1. Clutch Slave (possibly worn)-this will cause soft or hard clutch pedal feel, slipping clutch, unintended clutch release, hard gear engagement, no/insufficient clutch movement.

*2. Clutch pedal Mounting Plate (possibly cracked)-this will cause improper gear engagement, hard gear engagement, soft pedal feel, insufficient clutch movement.

*this plate is located above the clutch pedal itself, apply pressure on the pedal with one hand while inspecting the plate for fatigue cracks(use a bright flashlight). This is very common on these models. This problem will eventually get worst and most mechanics never figure this out.

more questions email me at gimconsulting@ymail.com!!

Mar 15, 2010 | 1989 Toyota Pickup SR5

1 Answer

Clutch problem


you still have air in the system very hard to bleed is the slave and master dry look under the dash at the master where it comes through the fire wall to see if it is wet some times you need to power bleed them

Feb 02, 2010 | 1991 Toyota Pickup

1 Answer

Replace clutch slave cylinder S10 89 2.5 standard


I would not replace clutch slave, take my advice and replace the master and slave unit. Though for the moment this is more expensive, unless you have a perfect master cylinder, the new slave cylinder will destroy it in a hurry. It is cheaper to buy them together rather than separate.

Sep 09, 2009 | 1988 Chevrolet S-10

2 Answers

I need to bleed my clutch in my 89 nissan pickup


if you have just instaled a new clutch you need to make sure the clutch disk has not ben instaled back wards and all the bolts holding the pressure plate are torqued evenly if eather is not corect the slave cyl will extend but not relace the clutch, if you have some one step on the clutch and it moves 1 to 2 in the problem is in the pressure plate or clutch disk,

Jul 06, 2009 | 1987 Nissan 300ZX

1 Answer

New master and slave still have no petal pressure or clutch


Was the slave cylinder bled correctly? If that's all set then that would leave the throw-out bearing and/or clutch assembly.

May 31, 2009 | 1991 Nissan Pickup

1 Answer

Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre


To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Mar 04, 2009 | 1994 Isuzu Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...