Question about 2002 Saturn VUE

1 Answer

Need to replace slave cylinder clutch goes to floor without any pressure. Does the transmissin have to be taken out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Transmission stays in. Buy a Haynes manual for your model and it shows how to replace slave cylinder.

Posted on Sep 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing and bleeding of clutch slave cylinder


If it goes to the floor you have either blown out slave cylinder or master cylinder, no two ways about that.

Jan 10, 2017 | Cars & Trucks

1 Answer

My 94 f150's clutch was spongy and now it goes to the floor and won't come back up, there is no pressure, what do I do?


check the slave cylinder but I suspect that the clutch master cylinder needs replacing. If that is the case replace the slave cylinder as well as it will be close to failing as well

May 01, 2015 | Ford F-150 Cars & Trucks

2 Answers

Clutch feels loose,no pressure. gears are stuck, shifter wont moveis it the clutch adjustment?


The Clutch Master Cylinder or the Clutch Slave Cylinder has a leak. From under the dashboard, located the Clutch Master Cyliner Boot and pry one side open. If hydraulic fluid drips out, the piston seal(s) in the cylinder are worn. You'll need to replace the cylinder.

Dec 27, 2014 | 2003 Chrysler PT Cruiser

2 Answers

Replaced whole clutch and slave cylinder on 1996 Toyota T100 2wd 2mos. ago. Today while driving the clutch hit the floor. I did'nt see any fluid leakage. Any ideas.


Sounds like you need to bleed the system again, or you have an air leak. try bleeding again and just check your fittings for tightness.

Jan 20, 2011 | Toyota T100 Cars & Trucks

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

Clutch pedal goes to floor no preasure filled and bled slave cyl same result


Hi:
If you have bled the system, you are down to either having a bad clutch master cylinder, or a bad clutch slave cylinder. You could eliminate the slave cylinder by removing the line and capping it off, and if you have a firm pressure on the clutch pedal ( don;'t try to push it down, just check for pressure!) then your slave cylinder is bad. If you cap off the line, and bleed the system, and the pedal still has no pressure, then your clutch master cylinder is bad!

Apr 15, 2010 | 2004 Chevrolet Cavalier

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

2001 ford ranger clutch


have you check the slave cylinder to see if its moving when someone puts there foot on the clutch.
And check the adjustment on the master cylinder.

Sep 18, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
2002 Saturn VUE Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...