Question about 2001 Ford Escape

2 Answers

I have a ford escape jeep 2001 model.and its overheating do I remove the thermostart ?I am using it in africa it was sent to me from america.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

IT IS NOT A JEEP!!!!!!! ITS AN SUV! JEEP IS MADE BY CHRYSLER CORP NOT FORD. QUIT CALLING SUV's, JEEPS!!!!!!!

Posted on Sep 09, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If it has coolant in the radiator , then it has to be the thermostat or a clogged radiator. Probably thermostat.

Posted on Sep 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rotors stuck 2001 ford escape


yes they freeze on because the factory doesn't use No Seize grease. Seriously, try a bigger hammer.
Hit it between the studs.

Oct 08, 2012 | 2001 Ford Escape

1 Answer

What size Allen wrench for 2001 escape front caliper?


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Mar 11, 2012 | 2001 Ford Escape

1 Answer

2001 ford escape overheating


try replacing your radiator cap

Jan 02, 2012 | 2001 Ford Escape

1 Answer

Trans was overhauled, when car reaches operatring tempreture OD light comes, and tranny starts to shift a little fast. Then sometimes it will not come on at all... V-6 2001 escape. 91,000 is looks...


HAVE A SCAN FOR FAULT CODES , I HAVE SEEN FORD ECM'S NOT RETAIN A CODE IN MEMORY FOR A TRANS OVERHEATING , ALSO WHEN THE LIGHT COMES ON DON'T TURN OFF UNTILL SCANNED

Aug 16, 2010 | 2001 Ford Escape

1 Answer

How to remove the alternator in my 2001 Ford Escape


you must remove the front passenger wheel assembly, cv shaft, intermediate shaft unbolt the alternator and then remove the alternator bracket only then can the alternator be pulled out

Oct 13, 2009 | 2001 Ford Escape

1 Answer

2002 ford escape liftgate wont lock/unlock


the electronic sensor could be bad or the lock is physically jammed.

Feb 09, 2009 | 2001 Jeep Grand Cherokee

1 Answer

I have a ford escape 2001 v6,water was fulled in the tank


if it runs without overheating issues but doesn't move forward or reverse....check your transmision fluid level...if its too low the vehicle won't move but the engine will run just fine.

Jan 16, 2009 | 2001 Ford Escape

2 Answers

2001 Jeep Gand Cherokee wont start on first try


i have a jeep grandcherokee 2001 in africa. had ecu problem. sent the part to use for repaired and the part was returned and no fault is found. engine is turning but car wont still start. I now bought the crampshaft sensor and relays. can you please suggest what other problems the car might have? Is there a any main jeep dealer in senegal? West africa.

email: osy@talk21.com.

Jul 20, 2008 | 2001 Jeep Grand Cherokee

1 Answer

Change front wheel bearing 2001 ford escape.


you need to remove the spindle assy from the truck & press the bearing out & in   or you need to use a tool called the hub tammer to remove & install the hub bearing

Jun 28, 2008 | 2001 Ford Escape

Not finding what you are looking for?
2001 Ford Escape Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...