Question about Mercedes-Benz ML320

1 Answer

Engine won't turn over, sometimes it does and sometimes it doesn't. Sometimes when I put into park it will kill and then won't start for 3-4 minutes.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 784 Answers

It sounds like you have a electronic control problem. Have the Fuel relay control module checked out. This one controls fuel pump and the cold start valve also.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After hot engine wont start and smells like gas


Most likely causes are bad engine coolant temp sensor OR leaking fuel injectors. Bad engine coolant temp sensor will give computer false reading and computer provides wrong air fuel mixture. Leaking fuel injectors will load the engine with raw gas--just like flooding it. Try pushing the gas pedal to the floor and holding it there when cranking when hot. That forces the computer into "clear flood" mode and it shuts off the injectors. If it starts up with pedal down, that would be a sign of leaking injectors.

Jul 21, 2017 | 1999 Dodge Intrepid

1 Answer

2004 Honda Odyssey won't start or try to turn


You tried it in neutral but did you take it out of park and force it back into park? Just a suggestion since sometimes the switch that tells it that it is in park needs a bit of a nudge sometimes.

Sep 09, 2013 | Cars & Trucks

1 Answer

My 1988 dodge Dakota 3.9 3 speed automatic 2 w Dr.idles rough and sometimes dies at a stop light and won't restart unless I put the gassed peddle to the floor.when it does finally start I have to keep...


Replace your hose going from intake to brake booster ( vacuum leak) check all other hoses also. Clean the throttle body. And a tune up probably wont hurt either.

Jun 09, 2017 | Cars & Trucks

1 Answer

Put a new engine in a 1998 isuzu rodeo now it won't start. I thought it was the neutral safety switch because the R was on the dash and it was in park


This could be the problem. If your dash indicator is showing reverse but the transmission is in park it could be the safety switch. I'm not talking about the safety switch in the transmission though. In automatics they put a second switch to kill the starter from engaging. You need to adjust the linkage. If your shifter isn't actually on the column but the indicators are there is a cable that attaches the floor shift to the column and that is adjustable. Put the Floor shifter in Park and turn the column section nearest the dash by hand until you find park. Then adjust the cable length as needed. If all you have is the column shift it is still a cable adjustment. Set the emergency brake, drop the shifter to low 1 and adjust the cable linkage by loosening it on the transmission and manually move it all the way to low 1 then tighten it down then move the shifter to park and repeat teh adjustment process to verify that it is properly aligned. Lock the linkage back down and see if the vehicle will start, if it doesn't move the shifter to neutral and try to start the vehicle if the vehicle starts then check the column shift safety switch at the park position to make sure it is still in place and working. Typically, if the vehicle won't start in Park or Neutral it is more likely to be the Transmission neutral safety switch.

Nov 15, 2011 | 1998 Isuzu Rodeo

1 Answer

2004 Hyundai Elantra won't start, emergency flashers keep blinking, can't shut off, lights dim, can't jump start, clicking from under dash from relays. What could it be?


The 'Keyless Entry & Burglar Alarm System" is activated. You must 'Disarm' the system using the Keyless Entry Remove (Key Fob) to "Reset" the system. The reason the engine won't start is due to the burglar alarm - it has a "Starter Kill" circuit which is activated when the alarm is activated. The alarm must be DEactivated to DEactivate the 'Starter Kill' circuit.
Another way to start the engine is to get in the car, put the key in the ignition and turn it to 'ON" and wait 3 to 5 minutes until the emergency flashers stop/turn off. Afterward, you should be able to start the engine. NOTE: This does NOT reset the burglar alarm. It will go off again when you enter the vehicle without using the remote/key fob.

Sep 06, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

My x5 3.0i 2006 t won't start this morning but temperature, gas level clock were wrong so I turn the engine off and restart a couple times it won't start and I saw message trans. false safe...


no. I'd suggest to disconnect a battery for 15 mins, reconnect, wait for 5 mins and try to restart. If it doesn't help (sometimes there's a program block to prevent stealing equipment) call a dealer

Aug 04, 2017 | 2003 BMW 5 Series

2 Answers

I have a 2001 dodge grandcaravan 3.3 liter engine .the engine light came on so took it to autozone to have them read the error codes .they came up with failure of transaxle control module and pressure...


tcm is located in drivers side front wheelwell. will have to remove wheel and wheel well splash shield. unhook 60 pin connector and three screws holding tcm to vehicle. will have to set pinion factor and quick learn function via factory scan tool solenoid pacxk located below air cleaner on transmission facing front of vehicle

Jan 09, 2009 | 2001 Dodge Grand Caravan

1 Answer

No Start


Hi m30sec

There is a "Kill switch" on the shifter mechanism that prevents starting the engine unless the car is in PARK. This is a safety feature sp the car won't start and suddenly take off if it were in gear. This is usually a mechanical switch. I can'r say for sure where it is on a Cavalier. What I suggest you do is call a Cavalier dealer, ask for the Service Dwpt and ask one of the men where the gear shifter kill switch is located. I have found that most dealers are real good about helping in a situation like your. You are a potential future customer.

Hope this helps Good luck Liringh Ps Please leave a rating if appropriate. Thks

Nov 24, 2008 | 1995 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...