Question about 2005 Volvo XC90

Open Question

2004 XC90 Radio displayed "ALARM! Press exit to cancel."

Driving steadily along the interstate on a clear day - no problems whatsoever. Radio turned on to FM station I had been listening to several hours before and displayed the message "97.3 ALARM! Press exit to cancel."

Pressing exit turned the radio back off.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

griff842000
  • 9 Answers

SOURCE: "ALARM" text appears in Radio Display

the xc90 has fiber optic cable all date is sent trough and it make a loop from the dash cluster to the radio to the ecu. i would ask for a wire diagram and start with some wire. i had a pinched wire under the dash with the same issue.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to find out where the valet/override button is located on my car....trying to program a new keyless remote


1. Insert key into the ignition and turn it to the On or ACC position, turn off radio. (do not start the vehicle)

2.Press and hold DISP button on radio until settings is displayed.

3. Press Seek until FOB PROG is displayed .

4. Press Prev or Next and BEGIN will be displayed

5. Press DISP and programming will begin when PUSH FOB is displayed. Press and hold Lock and Unlock together until vehicle chimes. This will signal successful programming. May have to hold buttons up to 20 seconds. Hold Lock and Unlock on additional remote until vehicle chimes again.

6. Exit programming mode. Scroll to Exit and press DISP to exit programming.

If you don't have the original radio, it can be done with a scanner.

Mar 19, 2016 | 2004 Chevrolet Chevrolet Impala

1 Answer

I have a 2003 chevy impala and the low tire pressure light is on. how do i reset it


Using the exterior lamp switch

  1. Adjust all tires pressures to the recommended kPa/psi.
  2. Turn ON the ignition, with the engine OFF.
  3. Cycle the exterior lamp switch from OFF to parking lamps 3 times within 5 seconds.
  4. Use the scan tool in order to clear the TPM DTC.

  5. Using the RDS radio, if equipped
  1. Adjust all tire pressures to the recommended kPa/psi.
  2. Turn the ignition to ACC or ON, with the engine OFF.
  3. Turn the radio OFF.
  4. Press and hold the DISP button until SETTINGS is displayed.
  5. Press the SEEK up or down arrows until TIRE MON is displayed.
  6. Press the PREV or NEXT button to enter the submenu. RESET will be displayed.
  7. Press the DISP button, A chime will sound and DONE will be displayed.
  8. Scroll until EXIT is displayed.
  9. Press the DISP button to exit the TPM reset mode. A chime will sound to verify exit.
  10. Use the scan tool in order to clear the TPM DTC.


Nov 17, 2009 | 2003 Chevrolet Impala

2 Answers

How do I reset the low tire warning light?


TIRE PRESSURE MONITOR RESET PROCEDURE

IMPORTANT: There are 3 different ways to reset the Tire Pressure Monitor (TPM) system. After resetting, the TPM system requires up to 30 minutes of straight line driving in each of the 3 speed ranges to complete the calibration process.If the TPM system does not reset, or DTC C1245 remains current, refer to Diagnostic System Check - Tire Pressure Monitoring. For further information, refer to Tire Pressure Monitor Description and Operation.

USING THE EXTERIOR LAMP SWITCH
  1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
  2. Turn "ON" the ignition, with the engine OFF.
  3. Cycle the exterior lamp switch from "OFF" to parking lamps 3 times within 5 seconds.
  4. Use the scan tool in order to clear the TPM DTC.
USING THE RDS RADIO, IF EQUIPPED
  1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
  2. Turn the ignition to "ACC" or "ON", with the engine OFF.
  3. Turn the radio "OFF".
  4. Press and hold the "DISP" button until "SETTINGS" is displayed.
  5. Press the "SEEK" up or down arrows until "TIRE MON" is displayed.
  6. Press the "PREV" or "NEXT" button to enter the submenu. "RESET" will be displayed.
  7. Press the "DISP" button, A chime will sound and "DONE" will be displayed.
  8. Scroll until "EXIT" is displayed.
  9. Press the "DISP" button to exit the TPM reset mode. A chime will sound to verify exit.
  10. Use the scan tool in order to clear the TPM DTC

Oct 11, 2009 | 2003 Chevrolet Impala

1 Answer

"ALARM" text appears in Radio Display


the xc90 has fiber optic cable all date is sent trough and it make a loop from the dash cluster to the radio to the ecu. i would ask for a wire diagram and start with some wire. i had a pinched wire under the dash with the same issue.

Aug 26, 2009 | 2005 Volvo XC90

2 Answers

No sound and cd read Paused


I had the same problem a few times. I found that it went into pause mode when the CD was playing and the volume was turned down to zero. Try turning the volume back up. The CD should exit pause mode.

Aug 06, 2009 | 2005 Volvo XC90

1 Answer

Reset message center window


THIS SHOULD HELP YOU

Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.

Jul 02, 2009 | 2004 Chevrolet Impala

3 Answers

2004 Chevrolet Impala tire pressure light guage


1. turn the ifnition to ACC or ON and turn the radio off
2. press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed
3. press the SEEK up or down arrow to scroll through the main menu
4. Scroll until TIRE MON appears on the display
5.press the PREV or NEXT button to enter the submenu. RESET will be displayed.
6. press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.
7.Once the monitor has been reset, scroll until EXIT appears on the display
8.Press the DISP button to exit programming. A chime will be heard to verify exit.
The system completes the calibration process during driving
This only works if you have a RDS system on the radio.

Jun 12, 2009 | 2004 Chevrolet Impala

1 Answer

2004 Chevy Impala Keyless Entry System Stopped Working


HOPE THIS HELPS YOU MIGHT WANT TO REPROGRAM THAT KEYLESS ENTRY FOB.. JERRY
. Turn the ignition to ACC or ON and the radio to off. Do not crank the engine.

2. Press and hold the DISP button on the radio for at least five seconds until settings is displayed.

3. Press the SEEK up or down arrows until FOB PROG appears on the display.

4. Press the PREV or NEXT button to enter the submenu. The current selection will have an
asterisk next to it. BEGIN will be displayed.

5. Press the DISP button to start programming. When the message PUSH FOB flashes, press and
hold the LOCK and UNLOCK buttons on the first transmitter at the same time for 15 seconds. A
chime will be heard to verify the transmitter is learned.


6. Repeat Step 5 for each additional transmitter up to four remotes total. You do not need to press
the DISP button again, just press down the LOCK and UNLOCK buttons on the next transmitter
to be learned to a maximum of four transmitters per vehicle.

The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.

EXIT (Exit Feature Customization Mode): This feature allows you to exit the vehicle customization programming.
To Exit:
1. Scroll until EXIT appears on the display.
2. Press the DISP button to exit programming. A chime will he heard to verify the exit.

Apr 27, 2009 | 2004 Chevrolet Impala

2 Answers

Need a clock.


in the radio display

Mar 22, 2009 | 2004 Volvo XC90

2 Answers

Low Tire Pressure Alert won't Clear


2 ways disconnect the battery for about 5 minutes or hook up an obd II and erase the codes

Mar 22, 2009 | 2002 Chevrolet Monte Carlo

Not finding what you are looking for?
2005 Volvo XC90 Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...