Question about 1990 Oldsmobile Cutlass Ciera

1 Answer

My 1990 Oldsmobile Cutlass Ciera engine keeps stalling but cranks and drive great. After it stalls, it will start up after one or two cranks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Fuel filter or pump. Get the pressure checked

Posted on May 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1990 Olsmobile cutlass ciera will stall if I accelerate past 15-20 miles an hour


Manually shift the gears to see if it does better. Maybee, the ttc solenoid engages early and stalls the engine. Trans.Torque Converter

Dec 03, 2013 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Engine stalls at 50mph to 60mph


Use a bottle of yellow HEET dry gas to remove any moisture problem in the fuel.

Clean / replace air filter.

Nov 07, 2013 | 1990 Oldsmobile Cutlass Ciera

1 Answer

1993 oldsmobile cutlass ciera. Engine stalls when you stop


Checkk the EGR system for the EGR valve should open when the engine gets to operating temperature. If not the engine will stall out

Jun 19, 2010 | 1993 Oldsmobile Cutlass Ciera

1 Answer

My 1993 cutlas supreme stalls randomly while idling or driving , but restart right away


You will need to change the crank position sensor first and see if it corrects the problem. It is located behind the engine near the firewall. It's a bit tricky to get to it, you would need to rotate the engine forward then look under the exhaust manifold and under the cylinder closest to the drivers side. Use a 10 mm deep socket to loosen bolt. After replacement and it is still stalling then you will need to replace the ECM (vehicle computer). If it turns out to be the computer, go to your local junkyard to get an inexpensive replacement Click on the link below to view the CPS, it is around $22

http://www.partstrain.com/store/?N=0&Nr=AND(make:Oldsmobile,model:Cutlass+Supreme,year:1993,brand:Delphi,part:Crank+Position+Sensor)&ptc=S1171391678W45d204bec356b&ptid=ptc45891f6tnywz&id=Olqtv7cphi





Olds-Cutlass-Ciera.htm">http://en.allexperts.com/q/Oldsmobile-Buick-Repair-826/f/1992-Olds-Cutlass-Ciera.htm

Apr 12, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

93 olds ciera stalls when slowing down or stoping


tcc stuck try unpluging it and see if same but dont drive with unpluged will burn up transmission also could be fuel pump . or crank shaft postion sensor . try the tcc first then vheck fuel presure , and then check for codes with scanner

Jan 28, 2010 | 1993 Oldsmobile Cutlass Ciera

2 Answers

Stalls when hot


Try a crank sensor. It's just above the oil pan center between the engine and transmission. Look and see if the old one is cracked.

Jul 13, 2009 | 1989 Oldsmobile Cutlass Ciera

1 Answer

1992 olds cutlass ciera keeps stalling out is there a main relay switch or ignition module switch that can be replaced? Where is it?Anyother ideas what could cause it to start, drive a few blocks, then...


could be a crankshaft position sensor located on the back side of the engine. There is a two wire plug on it and should be close to the freeze-out plugs. you will need an 8mm wrench to remove it.

Apr 22, 2009 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Stalling


does it also stall when u put it drive to if so it might be ur torque convertor not unlucking u can unplug the wiringplug on the transmission see if that helps

Apr 14, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Car wont idle, dies and shifts eratically


Hello;
It definetly sounds like a vacuum leak problem. The vacuum hoses are routed to perform various functions for the engine and transmission. They can be very difficult to track down. They are small diameter black hoses and start at the intake manifold (the source) and go to their respective locations.
They could be cracked, oil soaked, loose fitting, or disconnected to name a few problems to look for. Take it to a mechanic if you do not feel comfortable replacing the hoses.
Thanks;
Rich
RPM Northwest

Jan 22, 2009 | 1990 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1990 Oldsmobile Cutlass Ciera Logo

Related Topics:

518 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...