Question about 2004 Mitsubishi Endeavor

1 Answer

I need to look at my sub, too

Buzz's like it has worked its way loose.

Looks like a solid panel enclosure covering the sub.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 333 Answers

While the rear subwoofer does fail, it is often misdiagnosed because of a rattle in the vicinity.

Try removing the little fold away hooks near the subwoofer (philips screws) and see if your problem goes away.
If it is still there, loosen the panel and see if it goes away.
If it does not, more than likely the speaker has in fact failed.

Most subwoofer buzzes have been either the little fold away hook or the wire harness just behind the subwoofer.
Actual speaker failures are much more rare.

Posted on Sep 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm wanting to put my subs in the bed of my truck, how can I do this without rain messing them up ?


You need water-proof speaker enclosures.

You can build your own to save some money or purchase some pre-built ones.

Google "waterproof speaker enclosures".

Jun 01, 2014 | Cars & Trucks

1 Answer

How to replace a 2006 scion blower motor


cab heater a/c blower?
did you apply 12vdc to it directly and its dead>?
scion not corolla (corolla is easy)
tc,xa or xb>>>> no clue, so will look at tc.

but no matter what, i hot wire the blower, first. everyone does.
and the FSm too, it tells you step by step how to do the test.
sorry if all this is old hat, most here dont know this.....
if the blower works hot wired, its good.

ok the FSM covers this job, getone.
or, login in to alldata.com and read how.
that is what we do, so we can plan our time.

TC
. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL WARNING Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER
  • Remove the instrument panel sub-assembly upper
3. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY LOWER
  • Remove the instrument panel sub-assembly lower
4. REMOVE ECM
5. REMOVE AIR DUCT
6. REMOVE BLOWER ASSEMBLY

it looks like the blower just drops out the bottom, did you look?
it has 3 screws hold the motor assy to the main casing.
and the plug is there pin 2 is hot, pin 1 is ground
hot wire pin 2.
facing motor, with conn, at 12pm, pin 2 is LEFT.
the FSM shows a photo of that. and the full steps.


Feb 09, 2014 | 2006 Toyota Corolla

1 Answer

I'm trying to install an amplifier and sub in my


In the trunk or rear space there are plastic panels that cover the rear wheel mounts (solid steel bolts under the panels) I installed a Kicker Comp amp and sub in my wife's Pt cruiser and that was perfect. No engine noise or reverse accelorator sound at all. Has been in for 5yrs now without a need to touch anything.

Mar 13, 2012 | 2003 Chrysler PT Cruiser

1 Answer

Instrument panel light displays comes on not sure what it represents : It is a picture of a car and looks to be a srew coming out the rear passenger side and is orange in color: Something is causing the...


The light is telling you the gas cap is loose. The noise is coming from the belts? The blower noise is normal. That is your secondary air injection pump.

Jul 09, 2010 | 2005 Volkswagen New Beetle

1 Answer

My lighter outlet and rear power source does,nt work.Is this a fuse problem?


Most likely . Check fuses . If it is not solid and looks melted in fuse it is blown. Also have seen wires come loose from back of outlets.

Jun 14, 2010 | 2003 Chevrolet Venture Passanger

2 Answers

Speaker removal


Good day,
In your trunk there are 2 small amps. The first amp is connected to your car speakers. The second amp is connected to your subwoofer. Once you locate the subwoofer amp. Your subwoofer amp will be the amp close to the sub enclosure. Unplug the subwoofer from the amp. Your next step is to unscrew the 4 10mm bolts so that you can remove the sub enclosure. At this point you can now remove the enclosure. It will take a some time as it always seems to be up there pretty good. But once it starts to move it should come out with little work. I hope this helps with your removal of the subwoofer.

Mar 08, 2010 | 1995 Lincoln Town Car

1 Answer

1998 airbag light comes on and off. when light is on the spedometer and rpm dials go to zero when airbag light goes off they work again. This is not a continous problem but does it off and on.


There is a loose connection (or corrosion) where the instrument cluster attaches to the wiring harness mount. Remove the screws (2) from the dash cover below the steering wheel and remove the panel. Remove the defrost vent cover (just lift carefully, it only snaps into place. Remove the screws around the cluster panel cover and remove the cover. Remove the the instrument cluster (it pulls straight out toward you) and make sure the wires are not corroded. Make sure the wiring harness is firmly attached to the metal bracket that holds them in place. Carefully push the instrument cluster back into place. While firmly holding the cluster in place, install and tightnen the screws that hold the cluster. After tightening, wiggle it and make sure it's solid. Start your Jeep and make sure everything works. Shut jeep off and install the rest of the panels in the reverse order of removal. This should fix your problem. What happens is, the cluster becomes loose, speedo quits working (sometimes all other gauges quit also) and gives an airbag code.

Nov 13, 2009 | 1998 Jeep Wrangler

1 Answer

2005 Lincoln Aviator. Replace busted speaker third row seat??


the sub panal doesnt come off seperate you will break it if you try and you will need to remove the whole side panal its e-z afer the panals removed good luck and remember dont force or pull to hard

Mar 19, 2009 | 2004 Lincoln Aviator

2 Answers

Removal/replacement of sub woofer


You need to fold the drivers side seat forward. 
You have a compartment on the drivers side that is identical to the passengers side storage box and works the same way. The top of the panel on the drivers side is hinged like the passengers side. Pull up on the leading edge and it will open revealing the sub enclosure
Remove the speaker grill mounted in the carpet by carefully working a screwdriver under each of the corners and popping it loose, Once this is done you will have access to the 4 X 10mm bolts that hold the face of the unit. By pulling back the carpet a little you will reveal 2 more bolts at ether end of the enclosure. remove these and begin working the enclosure out carefully. It's a tight fit so take your time and work from the left side first. Once the left side is up high enough to reach the wires, unplug them from the side and finish removing the box. You can now make a choice. 
You can have your old speaker fixed "seach speaker repair" for $20-$40... or you can replace it with a new one.  www.twosrus.com can help you find a non-toyota replacement if you wish for reasonable money. 

Feb 24, 2009 | 1991 Toyota MR2

1 Answer

* * * Removal of Interior Trim Panel * * *


There are 2 finish covers on each side,looks like the one on the left is directly over ash tray?
You have to remove these 2 covers and there will be a screw located there. Remove these 2 screws remove the upper center finish panel by pulling outward to release the panel retaining clips.

Jan 30, 2009 | 2008 Ford F 250 Super Duty 4WD

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...