Question about 2004 Chrysler Sebring

1 Answer

I have 2004 chrysler sebring starter doesn.t engage but I have12.8. volts across battery and lights and hornworks strong

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

If it has worked recently and quit, you may have burned out windings and need a new starter. One way to check is have someone turn the key while you tap on the starter with a wrench or hammer. Strike the case of the starter pretty good. If the starter takes off, this is the problem. It may work a day or two after it gets going again but it WILL go completely out soon.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Starter is new and won't engage the flywheel.


2003 Chrysler Sebring 2.4L SFI 4cyl ' Repair Guides ...

www.autozone.com/.../repairGuideContent.jsp?...Starter...
AutoZoneAutoZone Repair Guide for your 2003 Chrysler Sebring 2.4L SFI 4cyl Engine Electrical ... Bad starter drive or flywheel-driven gear. ... Starter Spins Freely, Won't Engage ....Center the snapring on top of the shaft (use a new snapring if the original was ...Vehicle + Keyword: 04 Toyota Camry oil filter, battery 2005 Silverado.

Sep 18, 2015 | 2005 Chrysler Sebring Conv

1 Answer

My Chrysler Sebring 1997 v6 wouldn't start or have


Either the starter is defective or the ground wire is not on tightly!

Jan 14, 2013 | Cars & Trucks

1 Answer

2004 sebring will not start no radio


have you checked all the fuses.? how did it run before this? it sounds to be a few things. first pull the starter and have it tested . the fuse box is also a control module . they have problems going bad

Dec 19, 2012 | 2004 Chrysler Sebring Sedan

2 Answers

Car will not start, does not seem to be the


Check the cable connections. Make sure they are clean and a tight metal to metal contact.
Check starter relay with an ohmmeter to make sure it's good.
A part store will test battery, starter, and altenator for free in or out of the vehicle.

Dec 16, 2009 | 2001 Chrysler Sebring

1 Answer

Volts lights comes one; changed battery 3 days


have your alternator output checked. its a good idea that they check it while the light is ON. If they check it while the light is OFF, it may not show any problem.

Sep 28, 2009 | 2004 Chrysler Sebring

2 Answers

Chrysler 2004 starter doesn,t turn ,battery has 12.7 volts lights and horn works good but starter doesn't even click


My 2004 Sebring did just that. it was a fusible link. a tiny square box in there with the fuses. they are a cube that plugs in about 3/8" of an inch square. Find the bad one replace it and the starter starts working again.

Sep 08, 2009 | 2004 Chrysler Sebring

1 Answer

2004 Sebring GTC V-6 2.7L will not start


CHECK BATTERY VOLTAGE IT SHOULD BE 12.5 VOLTS.IF NOT HAVE IT CHARGED AND LOAD TESTED.IF ALL IS GOOD.CHECK ALTERNATOR OUT PUT.IT SHOULD BE 13.5 TO 14.5 VOLTS.WITH ENGINE RUNNING.IF ALL IS GOOD.HAVE THE STARTER SOLENOID AND STARTER CHECKED.IF ALTERNATOR OUT PUT IS LOW.HAVE ALTERNATOR REMOVED AND TESTED. DUE TO LOCKOUT FEATURE.MAKE SURE RADIO IS TURNED OFF BEFORE DISCONNECTING NEGATIVE BATTERY BEFORE REMOVING COMPONENTS.

Aug 10, 2009 | 2004 Chrysler Sebring

1 Answer

Have a 99 sebring just changed battery and car wonk crank


Hi I am Vortash when you turn the key is there a sound from the engine a clicking noise this would be the pre engaged starter motor solenoid trying to engage if you do then the starter motor may be jammed or faulty or possibly has a bad earth check all your body earthing straps .. ( the lights would work as they dont take much drain but the amperage of the starter motor wouldnt ) .
If after checking the earths you dont hear this then I would suspect that the ignition switch is at fault and the starter motor contacts in the switch have burned out or the starter relay hope this is of help regards vortash

Jul 22, 2009 | 1999 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...