Question about 1983 Mercury Zephyr

Open Question

I need front pass fender and headlight trim for this car

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to Replace Headlight Bulb on 2005 Prius?


Remove fender well trim ( a few screws)
Remove front bumper COVER (not the bumper- the plastic cover)
About 14 screws. Mostly on the underside, get a creeper, and a few
on the top.

Remove the (left or right side) Headlight assembly ( a couple more screws).
One assembly contains the headlight, turn signal and running light. Unplug
the electrical connector from the assembly. All bulbs remove from the back
of the headlight assembly. Headlight is held in place by bail wire, smaller
bulbs are 1/4 turn.

Oct 20, 2016 | 2005 Toyota Prius

1 Answer

How do I remove the front fender on a 1975 Triumph TR6


Start with removing all the trim on that render, the grill, the front bumper and the headlight trim etc. Remove the Front tire then locate and remove the screws holding the fender in place (see digragm/pic)

Jan 10, 2015 | Triumph Cars & Trucks

1 Answer

I need to know which fuse number for lights


Turn Signal (Right) white/tan (F), white/yellow (R) + TIPM, green 16 pin plug, pin 3; green 26 pin plug, pin 4
The TIPM (Totally Integrated Power Module) is in the engine compartment, on the passenger side fender.

Headlight white/brown -1.2K ohms [2009 = same] headlight switch or instrument cluster, gray 26 pin plug, pin 3
AutoLights same as headlight
Reverse Light white/lt. green + [2009 = same] passenger kick, harness to rear
Left Front Door Trigger purple - [2009 = VIOLET] driver kick or instrument cluster, white plug, pin 3
Right Front Door Trigger purple/white - [2009 = VIOLET/white] pass kick or instrument cluster, white plg, pin 16

Jun 25, 2011 | 2009 Dodge Challenger

1 Answer

My 2005 Avensis sedan front windscreen washer does not work - wipers do still opperate. Where is the fuse for this located and what else could cause this problem?


PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

May 15, 2011 | Toyota Passenger Cars & Trucks

1 Answer

HOW DO I CHANGE DRIVERS SIDE FRONT SIGNAL LIGHT


Best way to access the turn signal light is by dismounting the plastic inner fender. It is simpler than it seems. This unit is held in place by self locking plugs. Use a small screwdriver to pull out the inner section of the plug, and pull it out. There are about 4 or 5 of these plugs aligned with the trim of the wheel well opening, but you need to unplug just 2 or 3 to reach the back of the headlight assembly.
Dismounting the whole headlight assembly is much, much difficult.

Feb 17, 2011 | 2002 Honda Accord

1 Answer

Changing the headlight on a 2006 pontiac g6


To replace the headlight bulbs.You need to remove the head light assembly out.The head light assembly is held by 2 to 3 three screws on each side. You need to remove those screws first.The front trim will get loose,the front trim is held by pins.The pins are of plastic and easy to release.Just release this pins and the front trim will get completely loose and can be easily taken off/. The head light assembly is in the front fender.Once the front trim is removed the head light assembly can be easily removed from front fender compartment.If its bit tight there,then you can use a screwdriver to give it a pull towards out.The head light bulbs can now be easily seen as well as easily removed now.Turn the bulb socket counterclockwise to remove the bulb from the bulb assembly. -------- Keep updated for any more queries.Thanks.

Oct 14, 2010 | 2006 Pontiac G6

1 Answer

How do I change the headlight? (passenger side)


There are three screws that holds the head lamp in place, but first you have to remove the right side radiator cover, remouve the front grill (4 screws), remouve the head lamp lower trim (one screw behind the grill and cliped at the fender), then remouve the front grill mounting bracket (2 screws) then you'll finaly reach the 3 headlamp screws (2 on top and one behind the lower headlamp trim)
Good luck
Slant6Nova

Oct 24, 2009 | 1998 Cadillac Catera

1 Answer

Remove right front fender on 2005 odyssey


NO 2 BOLTS ON TOP OF FENDER UNDER HOOD 1 BOLT BEHIND PLASTIC TRIM BY MIRROR PULL THIS PIECE BACK TOWARDS MIRROR OR IT WILL BREAK TABS OFF 1 BOLT UNDER ROCKER TRIM 1 SCREW INTO ROCKER AND 1 SCREW BEHIND PLASTIC SHROUD GOING INTO BUMPER FROM UNDER NEATH PULL BUMPER BACK SLIGHTY AND YOU WILL SEE A WHITE PLASTIC CLIP PULL BACK AND BEHIND THIS IS A BOLT REMOVE HEADLIGHT CLIP FROM FENDER AND LOSEN BOLT BY HINGE NOW FENDER SHOULD COME RIGHT OFF BOOK IS 2 HOURS TAKES 1 HOUR TO REMOVE BUT GOES ON IN ABOUT 30 NINUTES

Mar 16, 2009 | 2005 Honda Odyssey

1 Answer

2002 honda oddessey: how do you replace the passenger headlight assembley


Yes, it is very involved. According to the Haynes manual you will have to first remove the radiator cover, the radiator grill, the inner fender splash shield pins (attached to the splash shield and front bumper cover), the front bumper cover, and finally the headlight housing. A DIYer can do this, but I recommend that you spend the $15 and get the Haynes manual because the pictures alone are worth it. Oh, and get a trim panel removal tool as well (cheap).

Jan 24, 2009 | 2002 Honda Odyssey

1 Answer

97 F-350 Headlight door removal


The front couple bolts (enough to fold the inner fender wells) on the fender wells (plastic part around inside the wheel well). Take them out, I think i did 6. Basically, just do what you have to do to fold the front part of that plastic inner fender well enough to see behind the parking light, then you need to remove the parking light/corner light assy. and once they are out you can reach the final screws required to remove the headlight trim rings. Also there are a few people on EBAY that are selling replacement headlight/parking/corner light assemblys that have clear outer lenses that dont get all yellow and foggy as the stock ones do. I bought smoked ones that have a light tint to it and they have projector caps so you can use HID kits and get a nice beam. something you might want to look into if your going to do the trim rings since its kind of a p.i.t.a.

Oct 15, 2008 | 1997 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...