Question about 2003 Chrysler Town & Country

Open Question

Rearview Drivers side mirror got ripped off and I'm trying to rewire it. I have a red and white wire, does the red and white hook together? I know wherre the red goes, but Im at a loss as to where the white goes

Posted by on

  • mr_dsmith68 Sep 08, 2009

    I have the mirror reassembled, just need to know what wire goes where

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75197 Answers

SOURCE: Rearview Mirror looseness

There is a tiny set screw on the mirror, tighten it.

Posted on Sep 10, 2008

SOURCE: 2007 Chrysler Pacifica

where is the spark pluga located on a 2007 pacifica

Posted on Jan 05, 2009

  • 2 Answers

SOURCE: 2003 Sierra rearview mirror

replace outside sensor

Posted on Feb 28, 2009

redbeard00
  • 957 Answers

SOURCE: Rearview Mirror Adhesive

The product does work fine, you can try it again. Make absolutely sure that all of the old adhesive has been removed, I use a new, sharp razor to remove the old stuff on both surfaces. Be sure NOT to touch either of the clean areas with your fingers. If you do, take acetone and wipe that part clean. follow the directions and good luck.

Posted on Jun 09, 2009

  • 104 Answers

SOURCE: can not find the set screw for this inside rearview mirror to rea

There is a little opening at the bottom of the mirror mounting part; gently push a small, flat screwdriver into it and slide the mirror off.

Posted on Jul 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Had a Bluetooth receiver installed and now my onstar does not power up on my rearview mirror.


The orange on white on Chevrolets are hot feeds, sounds like it got disconnected.

Mar 11, 2015 | 2006 Chevrolet Tahoe

1 Answer

Installing a frarview moniter


use a multi meter to check which wires have 12volts

Jul 19, 2013 | Honda Cars & Trucks

1 Answer

How do I remove a front left panal from a 2001 cadillac.


Hi, to remove the front door panel, remove the plastic surround from the inside door handle. It contains the seat switches and door lock switch. It is held in place by four pressure clips, so you should be able to pull straight out. Remove the wires to the switches. Next remove the window switches by inserting a small, flat screwdriver under the forward end by the window lockout switch. Carefully pry upward. Remove the wires if you want to make removing the panel easier.
The triangular panel on the inside of the rearview mirror will need to be carefully pulled inward but NOT REMOVED. You might be able to do this with just your hand. Remove the white/red marker/courtesy light at the back side of the door panel. A small flat screw driver at the back side should release it. Remove the wire. There are two phillips screws that need to be removed. One is in the opening where the window switch panel was, the other is behind where the red/white light was. After those two are removed, grasp the door pull handle and pull STRAIGHT UP. Don't try to pull inward.

Jan 29, 2011 | 2001 Cadillac DeVille

1 Answer

Cracked mirror only, mounting and other parts are functioning well. Can I purchase a mirror only and if so, where?? This is for 2006 Pontiac Grand Prix and the passenger side mirror is cracked but works...


Hello, yes the glass can be replaced. you will need to see your local GM dealer for the glass. real simple to replace.





  • Carefully push the outside rearview mirror face on the inner edge, near the front door window glass, to allow access.
  • Insert a large flat-bladed screwdriver in the slot between mirror lens and the mounting base.
  • Grasp the mirror face firmly and pull it from the mirror body.
  • Remove the outside rearview mirror case from the outside rearview mirror housing and disconnect the heater wire, if equipped.






  • Using the palm of your gloved hand, press firmly on the center of the glass until the case seats onto the motor.
  • The mirror will make a snapping noise when properly seated.
  • Inspect the mirror for proper operation.


  • cf49034.gif

    f845709.gif

    Jul 03, 2010 | 2006 Pontiac Grand Prix

    1 Answer

    I have a 2000 Buick Lesabre inwhich my blinkers aren't working Could this be due to when they rewired my drivers door after the wires were cut


    if its a mirror blinker yes,, if its on the car front and back only on one side, the rewire was a bad one and only one side of the car is not working,, ie the side that was rewired its likley they missed it out, if both sides are out try changing the flasher relay first

    Nov 05, 2009 | 2001 Audi A4

    1 Answer

    Trying to connect a teekonsha voyager brake control to a 2003 expedition


    Their should be a 6 pin conector that only 4 pins are used somtimes a 5th wire is installed for illumination, don't worrie about using that one. The connector is located in one or two different spots, the most popular place is under the dash on the drivers side just below the steering column the connector is grey. The colors are black or red / blue / green / white and sometimes a small black or brown wire is for illumination, don't worrie about that wire. Their are wiring harnasses for sell to hook the brake control through the conector, but if you do not want to buy an adapter hook the wires as followed: Vehicle Brake Control
    Black or Red Black
    Blue Blue
    Green Red
    White White
    Black is power in to the brake control
    Blue is the trailer brake feed
    Green is brake signal
    White is Ground for the brake control

    May 31, 2009 | 2003 Ford Expedition

    1 Answer

    Kia sorento 55 plate wing mirror


    1. Disconnect the negative battery cable.
    2. Remove the outside rearview mirror garnish.
    3. Disconnect the harness connector.
    4. Remove the 3 bolts and the outside mirror.
    To install:
    1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
    2. Connect the wiring harness.
    3. Install the mirror garnish.
    4. Connect the negative battery cable

    Jan 31, 2009 | 2005 Kia Sorento

    1 Answer

    Side View Mirror Wiring


    Just try matching from the outside to the outside, middle to middle, etc. or use a continuity tester against each pair until the light up. Solder the wires, do not use wire nuts.

    Apr 03, 2017 | 1996 Toyota Camry

    1 Answer

    Console wiring damaged during breakin


    Here is the wiring info for your radio. I have some other wiring diagrams but did not see anything related to your ac. Hope it helps and let me know if you want the other wiring diagrams. Also once you know what these wires are then you will be able to tell what wires are not related to your radio and might be able to figure out which wires are causing your other problems?

    Battery WHITE/YELLOW (+) RADIO HARNESS
    Accesory WHITE/RED (+) RADIO HARNESS
    Ground BLACK (-) RADIO HARNESS
    Illumination RED/BLACK (+) RADIO HARNESS
    Dimmer RED (-) RADIO HARNESS
    Power Antenna YELLOW/WHITE(+) RADIO HARNESS
    Amp Turn On YELLOW/WHITE (+) RADIO HARNESS
    LF Speaker (+) WHITE
    LF Speaker (-) ORANGE
    RF Speaker (+) YELLOW
    RF Speaker (-) BROWN
    LR Speaker (+) RED
    LR Speaker (-) GREEN
    RR Speaker (+) BLUE
    RR Speaker (-) BLACK
    Amp Location MOUNTED TO BRACKET IN RIGHT SIDE OF TRUNK
    Steering Cntrls YES
    Speed Cntrl NO
    Radio Security YES

    Oct 09, 2008 | 2002 Hyundai Accent

    1 Answer

    Custom Rear view mirror


    Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
    About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

    However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

    The best solution is to leave the original factory-installed rearview mirror in place.

    May 16, 2008 | 2006 Chevrolet Equinox

    Not finding what you are looking for?
    2003 Chrysler Town & Country Logo

    Related Topics:

    56 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...