Question about 1990 Hyundai Excel

Open Question

How do i pull the gearbox out of a excel 1990 5 i need to pull the engine out.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can you put a v6 out of a 1992 rodeo into a 1990 pickup that came with a 2.3l 4cylinder?

Any engine can be replaced. Most of all you need to look at engine mountings and space, electrical harness + computer and then Gearbox and differential specs. 4 cylinder gearbox will not be very good with a 6 cylinder engine. you will have high refs but no speed. if you have older v6, you might get away with electronics as a lot of them a straight forward. need a bit of work but doable.

Aug 18, 2014 | 1990 Isuzu Pickup

1 Answer

Wher is tach connector to gearbox located?

THE tach on this car is electronic.. it does not connect to the gearbox.. If it is not shifting correctly .. check the speed sensor..

Jun 02, 2014 | Volkswagen Beetle Cars & Trucks

1 Answer

Why is it difficult to get x-type into reverse. It is a manual 5 speed., 2004 Jag

Most common cause is a worn clutch ,but obvious your american and not used to manual gearboxes as their is a knack for this and that is lift clutch a bit as you pull it into reverse or if the fault is in the gearbox stop the engine put in reverse and restart engine ,also select reverse more slowly ,ever seen inside a gearbox and how the reverse works ? lots of extreme pressure on the changing mechanism .

Feb 21, 2013 | 2004 Jaguar X-Type

1 Answer

Engine is idling at very high speed? how do i adjust idle speed?

their should be a screw some where on or near the caruburater loosen the screw but dont over loosen it, one little turn goes a long ways. i hope this information helps, Be careful and drive safe!

Feb 27, 2011 | 1990 Hyundai Excel

1 Answer

New clutch it's already install but still shift noising

Make sure there is enough transmission oil in the gearbox, without oil the synchro's cannot work so gearchanges will be slow and cumbersome. If filling the gearbox oil dosent help maybe you have gearbox damage - have the gearbox checked out.

Jan 25, 2010 | 1990 Toyota 4Runner

1 Answer

Will a 99 excel gearbox fit on a 97

as long as they are the same engine size it should be a match

Jan 24, 2010 | 1990 Hyundai Excel

1 Answer

Can the bands in a automatic gearbox out of a Hyundai excel 1998 model be tightened or adjusted without overhauling the gear box? If they can can some one tell me how i can do it.

honestly do not know ,used to do it on the old C4 and borg warner boxes ,have a look for any adjusters on the outside ,then drop sump and have a look up from underneath

Jan 04, 2010 | 1990 Hyundai Excel

3 Answers

Cltuch 97 excel

dont listen to them, easiest way is: remove air intake box(3 nuts)
remove nuts surrounding the outer gearbox(about 6) and then remove the gearbox mounts
lower the gearbox and move slightly to the drivers-side. best to put a block or jack under it. then take the fly-wheel off(marking where it sits against the clutch kit)
and then pull the clutch plate off, making sure all fingers are not bent. i picked up a full clutch kit 2nd hand for 25$

Nov 14, 2009 | 1990 Hyundai Excel

1 Answer

Tranny drop

make sure all bots etc are out, drive shafts diconnected support engine remove gearbox mount lower engine enough to slide gearbox out if all bolts are out and it still will not come apart you may need to just prise the bell hosing from the rear of the engine as it could well be just stuck

Mar 01, 2009 | 1990 Ford Escort

Not finding what you are looking for?
1990 Hyundai Excel Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides