Question about 1993 Chevrolet S-10

2 Answers

Need help mounting power window regulator on a 1993 s10 blazer and picure or diagram would be nice

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Take panel off other door and look how it is mounted, tis the best way.

Posted on Sep 08, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 246 Answers

Remove the door trim panel.

  1. Disconnect the negative battery cable.
  2. Remove the armrest bracket-to-door screws and the bracket.
  3. Remove the water deflector from the door.

The water deflector is secured by a strip of adhesive between the deflector and door, as well as waterproof sealing tape. Upon installation, make sure a good seal is achieved to keep water from entering the body. If necessary, use strip caulking as a sealant between the deflector and door.
  1. Raise the window to the Full Up position. Using cloth backed tape, tape the glass to the door frame.
  2. Disengage the electrical wiring connector from the window regulator motor.
  3. Separate the regulator lift arm roller from the window sash.
  4. To remove the window regulator motor from the door:
    1. Drill a hole through the regulator sector gear and backplate, then install a bolt/nut to lock the sector gear in position.



CAUTION The sector gear MUST be locked into position. The regulator lift arm is under tension from the counterbalance spring and could cause personal injury if the sector gear is not locked before the motor is disconnected.
    1. Using a 3 / 16 in. (5mm) drill bit, drill out the motor-to-door rivets.
    2. Remove the motor from the door.


To install:
  1. Position the motor to the regulator, then secure using 3 / 16 in. (5mm) rivets.
  2. After the motor is riveted to the door, remove the nut/bolt from the sector gear.
  3. Install the regulator lift arm roller to the window mount sash.
  4. The balance of installation is the reverse of removal. It is advisable to check operation of the system before installing the water deflector and trim panel.

sorry no picture

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a color code for the brake light wiring diagram for a 2000 s10 blazer


The S10 and the Blazer are identified as two different vehicles. The left stop light wire is YEL; the right is DK GRN. The center high mount stop lamp wire is LT BLU.

Oct 30, 2016 | 2000 Chevrolet Blazer

1 Answer

How do i replace power window in driver door of 2001 chevy blazer?


are you replacing the power window regulator ?follow this u-tube link for excellent step by step instructions , if not the regulator let me know and i'll see if i can help further
How To Install Replace Power Window Regulator Chevy S10 Blazer GMC S15...

Sep 19, 2014 | 2001 Chevrolet Blazer

1 Answer

1993 Chevy S10 Blazer Serpentine Belt replacement


You use a breaker bar to move the tensioner, remove the belt and use the tensioner to put it back. You draw the belt and pulleys on a sheet of paper before removing, otherwise there should be a small diagram of the belt and pulley positions on the fan shroud or radiator support.

Jun 25, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

Where is the computer on 93 blazer s10 how do you change it


For 1993 Chevrolet Truck S10 Blazer 4WD 4.3L CPI 6cyl the Engine Control Computer is located in front seating area, passenger side, behind dash, above glove compartment cavity, mounted on dash upper panel.

Hope this helps (remember to rate and comment this).

Sep 27, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Start hard runs rich


hi all the injectors and reg is inside the intake and are good about going bad. the top of the intake got to come off.

Jul 27, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

1991 Chevy Blazer S10 window motor installation


http://www.a1electric.com/s10motor.htm. This link has pictures and step-by-step instructions. I found it and have both sides to replace. Hope this helps.

Aug 08, 2008 | 1991 Chevrolet S-10 Blazer

1 Answer

Chevrolet Blazer S10 1993


i recomend getting a book from the auto parts store. it will have all the electrical diagrams. it costs less than $20.00 and will be a good investment. i have a book for all my cars and have never had to go to a shop.

Jul 09, 2008 | 1993 Chevrolet S-10 Blazer

2 Answers

Power steering


its on the pump. driver side of the pully system.

Jul 01, 2008 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...