Question about 2007 Buick Rendezvous CXL SUV

1 Answer

Cannot program garage door transmitter

I do not have a manual and was wanting to set the garage door transmitter on my 07 Buick Rendezvous...any advice?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 1,000 Answers

Depending on the type of vehicle home remote system you have and the type of garage door opener installed will determine how you program the system in your vehicle.
Below is a web address for the owners manual to your Buick. It will show you step by step how to set your Buick's remote system to open your garage door.
Good luck.
Regards,
http://www.extendedgmwarranty.com/owners-manual/buick/2007-Buick-Rendezvous.pdf

Posted on Sep 08, 2009

Testimonial: "Perfect, thank you!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The light in my Homelink system does not come on. Therefore it cannot be programmed.


The following are steps to programming a rolling code door opener to the Homelink transmitter in the Touareg.

The instructions in the owner's manual are correct, but after following them, my garage door installer and I discovered a few quirks and fixes for them.

It is important to park the Touareg in front of the garage door. Be careful not to park underneath it. rolleyes.gif

If your remote garage door transmitters are already programmed to your door opener, you need to do the following steps:

1. On the garage door opener itself, there is a learn button. Press and hold down the learn button until the learn indicator light goes out (approx. 6 seconds). (The learn button is near the antenna on your door opener.) By doing this, you have just reset the codes. At this point your remote door transmitters will most likely not work. This is o.k.

2. In the Touareg, press and hold whichever homelink button you want to program until the light above the homelink buttons slowly blinks. Continue to hold the button in and at the same time, hold your remote transmitter underneath the map lights and press the button. Continue to press both buttons until the homelink light rapidly flashes. Let go of both buttons.

3. You now have 30 seconds to press the learn button on your garage door opener. Press it once. The light will start to blink.

4. Go back to the Touareg, press and hold the homelink button you just programmed for 3 seconds until you get a blinking light. Repeat again. This time, it should open or close the door. The homelink button is now programmed.

5. Now that the homelink button is programmed, you now have to re-program your remote transmitters. Take the transmitters with you.

6. On the garage door opener, press the learn button, the light will blink. Now press the button on the remote transmitter. The light should stop blinking. Repeat the step if you have more than one transmitter. You should be all set. The homelink button should work in the Touareg and your remote transmitter(s) should also work.

In summary, the rolling codes in the door opener receiver have to be reset. For some reason, the Touareg has to be programmed FIRST. Then the remote transmitter units. If the remote transmitter units are already programmed, you will most likely not be able to program the homelink in the Touareg for a rolling code door opener.

------------------------------------------------------------------------

Original Launch X-431 DIAGUN III

Mar 14, 2013 | Cars & Trucks

1 Answer

I don't have the owner's manual for my 2002 GMC Yukon XL Denali. Do you know how to program the garage door opener?


I hope this helps.

Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the stop and reverse
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make
sure that you have followed the directions exactly as
described and that the battery in the hand-held
transmitter is not weak. If you still cannot program it,
move the hand-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to "Training a Garage Door Opener with
Rolling Codes" later in this section or contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
Be sure to keep the original hand-held transmitter in
case you need to erase and reprogram HomeLink.


Training a Garage Door Opener with a
"Rolling Code" Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see "Programming the
HomeLink Transmitter" listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the "Learn" or "Smartbutton" on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful
to have another person assist in programming
the transmitter.
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling-code garage door opener should now
recognize HomeLink. You may either use HomeLink
or the hand-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
www.gmcextendedwarranty.com

Dec 19, 2010 | GMC Yukon XL Cars & Trucks

1 Answer

Factory garage door opener


If this is the 3 button HomeLink Transmitter usually centered overhead above the rear-view mirror, this should work:

While the engine is turned off follow these steps to program up to three channels:
1. Decide which one of the 3 channels (one of the 3 HomeLink buttons) you want to program.
2. Press & hold the desired button through step 3.
3. When the HomeLink indicator light begins to blink slowly(this may take up to 30 seconds), hold your hand-held garage door remote about 1 to 3 inches away from the buttons & then press and hold the button on your garage door remote. Continue to hold both buttons until the indicator light on the HomeLink begins to flash rapidly(this may take up to 90 seconds).

If it still doesn't work, make sure the batteries in your garage remote are not weak, and try again moving the remote back & forth and left & right or turning it upside down while programming.

Also note HomeLink will not work with older garage door openers, especially not with ones manufactured before April 1st 1982.


Feb 18, 2010 | 2005 Buick Rendezvous

2 Answers

I need to program my new garage door opener to my 2004 buick rendezvous I dont have my manual to tell me how to do it help


go to the brand of garage door opener and usually under support they should have manuals for your model

Oct 29, 2009 | 2004 Buick Rendezvous

1 Answer

How do you program garage door transmitter


Look in the owners manual to find the proper sequence. Your garage door opener must be compatible with this new technology. Your opener should have a code learn button on it that must talk to your vehicle for it to work

Apr 22, 2009 | 2007 Buick Rendezvous CXL SUV

1 Answer

Program 2004 mercury mountainer garage opener


Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.

Apr 01, 2009 | 2004 Mercury Mountaineer

2 Answers

How do you program the garage door opener on a 1997 buick riviera. Bought it used, no owners manual.


You'll need to open the transmitter in the car and match the frequency to the garage door reciever, assuming you have the fob for the garage door, opening this will reveal a set of tiny switches. This combination is the frequency you need. Open the transmitter in the car, and place all of it's switches in the same position as in the fob. If this doesnt work, then the governing frequency isn't the same and there's not much you can do. Hope this helps!

Mar 10, 2009 | 1997 Buick Riviera

2 Answers

Universal garage opener


The solution is in the owners manual.If you want to program the "homelink transmitter" in your car,you will need a remote unit for your garage door opener to do this.It is fairly easy and straightforward.I programmed my 07 Pac and it works great.Good luck!

Mar 08, 2009 | 2005 Chrysler Pacifica

1 Answer

Program a garage door opener in 2004 buick rendezvous


I cannot find the 2004, but you can buy it from the dealer. You can download the 2003 and 2005 from this link. http://www.extendedgmwarranty.com/owners-manual/buick_owner_manuals.html

Nov 04, 2008 | 2003 Buick Rendezvous

1 Answer

Programming Garage Door Opener on Visor


A Buick dealership can do it for you.

Jun 20, 2008 | 2003 Buick Rendezvous

Not finding what you are looking for?
2007 Buick Rendezvous CXL SUV Logo

700 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...