Question about 1965 Ford Mustang

1 Answer

Removing gas pedal from 65 mustang

I bought new pedals for my 65 mustang, but I can't seem to remove the old pedal. There's a nut holding it on (loosly) but I can't remove it to replace my pedal pad.

help? =/

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Can't remember for sure but maybe there is an "E" clip or something similar on shaft that pedal is around, when removed, pedal slides off shaft?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

Wd-40 it for couple hours. You need to hold other end that is most likely stripped. Needle nose vise grip worked for me.:)

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Step by step instructions for replacing brake booster on a 1999 Toyota Camry


its my pleasure to answer your question how to replace the brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How to remove brake booster on 1999 Toyota Camry


The following steps will help you to replace a Toyota Camry brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How do i replace the brake booster on a 98 Mercury villager


12 specific steps will help you :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the vacuum brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Sep 24, 2013 | Cars & Trucks

1 Answer

Could my problem be fuel pump or carbuerator starting my 65 mustang it takes 3 to 4 times and i have to hold gas pedal down so it doesnt cut out after going it will still cut out when i slow down o


this sounds like the carburetor is dirty internaly and needs a rebuild to correct the problem.if it was the fuel pump it would not matter if you held the pedal wide open or not it would not pump gas.you mention plug wires but not mention spark plugs specifically.these are the items that are normally replaced when a tune-up is done.plugs,cap rotor,points,condensor,plug wires if needed,air filter,fuel filter,set point gap,set ignition timing,adjust carb mixture.

Mar 02, 2012 | 1965 Ford Mustang

1 Answer

I have a 65 mustang with a 200. The spring on the carburetor linkage that returns the gas pedal to ideal position is held by chicken wire attached to the exhaust. I was looking for a diagram of how the...


On my '65 w/200 cid, the return spring is indeed hooked to a flange on the exhaust. Seemed a bit wierd, but that's what I've seen on other 200cid Mustangs.

Jan 24, 2011 | 1965 Ford Mustang

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

Clutch cylinder removal & repiar for toyota master ace surf 91 import


to removal clutch cylinder first remove the pin which holding cylinder and pedal it under just follow the pedal,then open the bonnet have look where fitted clutch cylinder loose the pipe just 10mm spanner then remove to nut which is 12mm spanner then it is out.
if you want to put new kit use to hold cylinder with vise then remove dust cover then remove carlip then just remove old.
to put the new kit clean first check also inside the cylinder if there any sine scratches if not use some brake oil put some in the cylinder before you put the new kit then fixed and plead to take air in the system.

Jun 13, 2009 | 1991 Toyota Land Cruiser

1 Answer

On a 1987 ford mustang, clutch makes rattling noise when pressed


No, you can change it in the car. Look up between the brake an gas pedals and you see the parts you need to remove. It's kind of tight up there but, it's a lot easier then removing the whole pedal assembly.

May 30, 2009 | 1987 Ford Mustang

1 Answer

Pulsating gas pedal in low speeds, if you go really easy on the pedal untill ~25, it will not pulse at all.


Make sure the carb is bolted tight to the manifold too. Loose nuts can cause this.

May 20, 2009 | 1965 Ford Mustang

1 Answer

How to fit a clutch master cylinder for c220 cdi


Remove the three 13mm nuts holding the pedal bracket to the bulkhead, this will give you more room to work but just as it's free to move about a bit. Undo the two 10mm nuts holding the cylinder to the pedal assy and the pipe union at the bottom of the cylinder. Pry off the clutch hose at the fluid reservoir. Release the circlip on the end of the cylinder rod on the pedal.
When you put the new one in feed the hose through first with a piece of wire so you can locate it at the fluid reservoir, loosley connect the union at the bottom of the cly, and pop the end of the cyl rod into place and replace the circlip. now try to relocate the long bolts into the cylinder body, it's a fiddle but can be done. Use a 3/8 drive to undo and re-do the 10 mm nuts as a smaller one seems better but doesn't have the reach. The rest is just common sense.

Aug 01, 2008 | 2000 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...