Question about 1999 Chrysler Concorde

1 Answer

I can't put my car into gear it acts like its stripped...what could this be

Posted by on

  • cbmay60 May 11, 2010

    just had trans put in last year now car will not move in any gear it even rolls when in park



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

It can happen but not very often,Is your other gears ok? if they are just pull you drain plug an see if you have alot of metal in it.If you do your supictions was correct,I hope the helps?.

Posted on Sep 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What could be the possible solution when the car acts like neutral in reverse

sounds like your reverse gear cogs in your gearbox is broken / stripped. gearbox strip down required...

Jan 28, 2016 | Cars & Trucks

1 Answer

I have a 2001 chevy tracker Manual transmisson The only gear it will move in is 4th When u try any other gear it acts like its in neutral Any ideas

The manual transmission uses a mainshaft that is locked in 4th and gives the 1:1 ratio. The rest of the gears come off the input shaft of transmission to a counter gear cluster then back up to output shaft. Either the input shaft gear or the gear on the counter shaft is stripped. That would cause the only fourth gear drive.

Feb 16, 2014 | Cars & Trucks

1 Answer

91 honda accord manual transmission was driving down highway and heard a loud noise pulled over now wont shift into gear

You may have stripped the clutch disc. This can happen when the clutch gets old and worn or if it has been abused by rough use. When the disc strips, there is no friction between the clutch disc and the pressure plate so the vehicle acts like its in neutral.

Dec 18, 2013 | Cars & Trucks

1 Answer

Today my 06 Chevy Trailblazer will go through the first couple gears fine. Around 30 mph it won't shift. It just acts like it just went into neutral. Engine revs and no power. Once it slows down and...

Sounds like clutch issue, if the car was that low on transmission fluid, obviously there is big leak somewhere, and depending on how long it was driven, one of the gears may have stripped or broke.

Might be a good idea to have a transmission shop or Chevy Dealer look at it.

Other possibility newer cars use a electronic control to tell the transmissions to shift, could be a possible issue there, but doesn't explain the transmission fluid issue.

Aug 25, 2013 | Cars & Trucks

1 Answer

Transmission not working right

I believe you have a slipping gears and looks like the gear box need overhauling. Take it to an Automatic Transmission Specialist to Diagnose.Do not leave it and use it any further,surely you will cause serious damage and cost.

May 25, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Smooth idle until put in gear then acts like its going to die

Is the check engine light or service engine soon light on ?

Feb 03, 2013 | 1997 Chrysler Concorde

1 Answer

When i am putting the car in drive and i start out it acts as if it is stuck in neutral and feels like i am running over rumble strips i put it in low gear and back up in drive and it is fine i thought...

let the car warm up to normal operating temperature and check the transmission dipstick. if it is low add transmission fluid in the tube the dipstick is in.

Nov 12, 2009 | 1998 Oldsmobile Cutlass

1 Answer

88 toyota p/u window arm removal

remove the window by un-doing the two bolts at bottom, then undo bolts that secure window mechanism to door. I think you will find that it is not the gear that is stripped. The shaft that supports the gearruns in a pressed steel bush, this is what will have worn. I just cleaned away the sahrds and tacked on a nut of the right size to act as a replacement bush.

Jan 02, 2009 | 1988 Toyota Pickup

Not finding what you are looking for?
1999 Chrysler Concorde Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides