Question about 1997 Chevrolet S-10 Pickup

1 Answer

How to replace turn signal lever for 1997 chevy S10 and how to get the steering wheel off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 426 Answers

send me an email address and I can send you the instructions in a text format

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a1997 Chevy 1500 and I am wondering were is the flasher relay at.


Most cars the flasher relays are up under the dash not far from the steering column. I had several makes of cars and they all were up there.

Jan 10, 2016 | Cars & Trucks

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

1 Answer

How to replace key switch in 1992 chevy s10


have to remove steering wheel then lock plate then turn signal switch then you can remove a screw that holds in the key cyl you need special tools to do this with not easy if you don't know what you are doing

Apr 08, 2010 | 1986 Chevrolet Chevy

1 Answer

How do you remove the ignition lock cylinder on a 1991 chevy cavalier


The ignition switch removal and installation procedure is given in , under steering, because the steering wheel must be removed for access to the ignition switch.

To remove the ignition lock:
CAUTION
You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.
  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.

3026ee6.gif

The steering wheel is splined to the steering column and held in place by a nut. Courtesy of General Motors Corporation - Service Operations.

Hope this helps (remember rated and comment this).

Mar 22, 2010 | 1991 Chevrolet Cavalier

1 Answer

2000 lumina turn signal lever broken off


its best to take steering wheel off and change it its faster and easier

Oct 05, 2009 | 1997 Pontiac Bonneville

3 Answers

I HAVE A 1984 CHEVY S10, I'M HAVING PROBLEMS WITH ONE TURN SIGNAL. IT WORKS SOMETIMES, AND OTHER TIMES IT WONT.


This could be the multifunction switch which is basically attached to your turn signal lever in that model, it could also be the bulb, or the connection to the bulb, I would start simple, just remove the bulb verify the connector is not burnt at contact points and the pigtail wire is fully connected.

Aug 27, 2009 | 1984 Chevrolet S-10

2 Answers

Replacing a flasher


SHOULD BE IN THE FUSEBOX UNDER THE DASHBOARD UNDER THE STEERING WHEEL. HOPE THIS HELPS. LET ME KNOW PLEASE. GOOD LUCK

Apr 14, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

No turn signals or high beams.


try headlamp switch witch is with your turn signal sin steering column

Mar 10, 2009 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...