Question about 2005 Dodge Ram 2500 Truck

Open Question

Power door locks will not function in only the rear doors

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Rear Door Electric Lock buzzing and stuck

It's the power lock solenoid. There is a tiny plastic piece that connects the solenoid (motor) to the door lock mechanism (thin metal rod or two). Likely, the plastic piece has become disengaged. This is by design so that if there is a problem with the mechanism the motor does not burn out. You will need to have the interior door panel removed to gain access to the interior of the door and the lock rod and solenoid need to be reconnected. The plastic clips used to go for $1-$2 when I worked in auto parts.

Posted on Jan 13, 2009

polarcycle
  • 1392 Answers

SOURCE: Remote door locks won't work

There is a flash for the body control module for this problem. You need to go to the dealership to get it performed though.

Posted on Mar 08, 2009

ftw1952
  • 10319 Answers

SOURCE: driver's side power window doesn't work nor the rear power window. inside lights flicker and power door locks click repeatedly when hitting bumps on the road.

You diffenently have a positive wire grounding out somewhere

Posted on May 23, 2009

  • 166 Answers

SOURCE: electric door lock not working

Any of these three causes may apply to your situation of your driver's rear door not power locking, specifically the malfunctioning of the 1) relay system, 2) switch motor, or 3) the switch/button itself. Here's a handy diagnostic article that explains this:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Locks_Power_Locks_Do_Not_Lock_When_Pressing_Locking_Switch_Button.htm

This should lead you to the correction of your door's failure to lock.

Brad

Posted on Jun 01, 2009

  • 580 Answers

SOURCE: rear door power lock--1996 Dodge Ram van (Roadtrek)-- won't open

Check all of your dash fuses inside the glove box if these are fine. Remove the door panel nd check to see that the wires have not come loose they tendto come loose from closing the rear door.

Posted on Jul 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 le sabre, power windows, door locks, side mirrors, not working all of a sudden


All - driver - passenger - front an back ? Look for broken wires inside the rubber boot from the body to the door ,driver side !

Power Windows Operation
Power Windows
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
If the status information to permit window operation is correct, the DDM sends the command to the door module controlling the window to move the window as requested.
Windows Power and Ground
The windows are powered by discreet power and ground circuits. These circuits are in the same dedicated connector as the window motor drive circuits.

PWR/WDO 30 amp circuit breaker located in the rear fuse box ,DRVMDL fuse 10amp located in the same rear fuse box . This power the driver door module (computer )

The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted.
The exterior key cylinders are wired to either the DDM or the passenger door module (PDM), depending on the location of the key cylinder. The interior lock switches are wired to the driver door switch assembly (DDSA) and the PDM. The DDSA and the PDM send the lock switch requests to the DDM over the simple bus interface (SBI) serial data circuit. The DDM then sends the lock requests to the RIM over the Class 2 serial data circuits.
The door lock operation modes are controlled by the rear integration module (RIM). The RIM examines the requested function from the DDM, or the remote function actuator (RFA), as well as the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. The RIM determines if a locking function is permitted, and commands the DDM to perform the function permitted. The DDM then sends commands to the rest of the door modules via the SBI to implement the selected locking function.
All programmable modes of lock system operation are stored in the RIM. The RIM checks the lock function program selected against the lock requests, the transmission selection and ignition key switch condition to determine if the requested function is permitted. If the requested function is permitted, the RIM then commands the DDM to perform the lock function over the Class 2 serial data circuits. The DDM commands the individual door modules to perform the lock function over the SBI serial data circuit.


GOOD luck your going to need it !

Mar 13, 2017 | 2000 Buick LeSabre

1 Answer

2002 Cadi Deville, can't get any locks to operate with remote or dash push buttons, the remote operates everthing but the locks! When the remote door lock is pressed, lites flash,horn blows locks not.


Power Door Lock Operation
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door, but the rear integration module (RIM), which is the master control for the door lock system, determines when the lock functions are permitted. The RIM receives and examines the requested lock function from the individual door modules, or from the remote function actuator (RFA) via the class 2 serial data circuit. The RIM also examines the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. If the RIM determines that a lock or unlock function is permitted, it sends a class 2 message back to the individual door modules commanding them to perform that Lock or Unlock function.
Power Door Lock Components
The power door lock system consists of the following components:
?€¢
Driver door lock switch


?€¢
Passenger front door lock switch


?€¢
LH rear door lock switch


?€¢
RH rear door lock switch


?€¢
LH middle door lock switch (w/ V4U)


?€¢
RH middle door lock switch (w/ V4U)


?€¢
Driver door switch assembly (DDSA)


?€¢
Driver door module (DDM)


?€¢
Passenger front door module (PDM)


?€¢
LH rear door module (LRDM)


?€¢
RH rear door module (RRDM)


?€¢
Left middle door module (LMDM) (w/ V4U)


?€¢
Right middle door module (RMDM) (w/ V4U)


?€¢
Driver door lock actuator


?€¢
Passenger front door lock actuator


?€¢
LH rear door lock actuator


?€¢
RH rear door lock actuator


?€¢
LH middle door lock actuator (w/V4U)


?€¢
RH middle door lock actuator (w/ V4U)


?€¢
Driver door cylinder unlock switch


?€¢
Rear integration module (RIM)


?€¢
DRVMDL fuse (10-amp)


?€¢
PASS MDL fuse (10-amp)


?€¢
RRDR MDL fuse (10-amp)


?€¢
Class 2 serial data link

Sep 27, 2016 | 2002 Cadillac Deville

1 Answer

Where is the control module for the windows and locks etc.


The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted. ( RIM ) is rear integrated module , under the back seat . Also a fuse box is also located under the back seat.
The door lock operation modes are controlled by the rear integration module (RIM). The RIM examines the requested function from the DDM, or the remote function actuator (RFA), as well as the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. The RIM determines if a locking function is permitted, and commands the DDM to perform the function permitted. The DDM then sends commands to the rest of the door modules via the SBI to implement the selected locking function.
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
Your best bet is take the vehicle to the dealer or a repair shop that knows how the system works . Are you familiar with GM class 2 serial data communication network ? You could inadvertently render your vehicle unable to start an run if the class 2 bus were to become shorted to ground .
You
Buick Class 2 Operation Diagnosis 1998

May 03, 2016 | 2000 Buick LeSabre

1 Answer

Why does my 2004 Chevy Silverado lock and unlock while in drive? When turned off and no keys in ignition the drivers door will unlock on its own a short time later.


Gremlins ! HA HA HA sorry ! First off a little bit on how they work an what all is involved in making them work ! There are a few control modules in the mix , switches ,relays etc...
Door Lock System Components
The power door lock system consists of the following components:
?€¢
The driver door module (DDM)

?€¢
The passenger door module (PDM)

?€¢
The body control module (BCM)

?€¢
The driver information center (DIC)

?€¢
The rear door lock switch

?€¢
The door lock relay

?€¢
The door unlock relay

?€¢
The liftgate lock relay--utility vehicles with liftgate only

?€¢
The reversible door lock actuators in each of the doors and liftgate

?€¢
LOCKS 20A fuse (rear lock/unlock relay supply voltage)

?€¢
ECC 10A fuse (liftgate lock relay supply voltage)

Door Lock System Controls
The power door lock system can be controlled by any of the following:
?€¢
A power door lock or unlock switch activation

?€¢
A keyless entry transmission

?€¢
An automatic door lock function

?€¢
A delay lock function

?€¢
Door lock cylinder switch activation

?€¢
Lockout Prevention

?€¢
An airbag deployment

The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
?€¢
The DDM (driver door lock actuator).

?€¢
The PDM (passenger front door lock actuator).

?€¢
The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.
The first place to start is have a factory or equivalent scan tool hooked up , one that can read BCM DTC'S - diagnostic trouble codes ! This could lead to a fix faster ! Watch these three videos !
Door Locks Go Crazy 1

Sep 16, 2015 | Cars & Trucks

1 Answer

2003 Cadillac STS door and truck lock quit working


I checked all the fuses and relays and all are in good shape???????
Did you check the correct one's ,that's the question ? And did you use a voltmeter or test light to check across the correct fuse's ? And how did you check the relay's ????? Videos on youtube on how to test a relay ! And using a wiring diagram or power flow diagram that shows all componets of the none working systems ., Plus you need to know how the thing's work . Data communication network is involved in the working of these thing's , Data messages from module to module !

The body control system consists of the following 3 modules:
• The Dash Integration Module (DIM)
• The Instrument Panel Module (IPM)
• The Rear Integration Module (RIM)
Rear Integration Module (RIM)
The various RIM inputs and outputs are described in the corresponding functional areas as indicated on the RIM electrical schematics.
The RIM functions include the following:
• Automatic level control
• CIGAR relay control
• Class 2 communication requiring RIM interaction
• Content theft deterrent
• Fuel door control
• Fuel level sensor input
• Heated seat control
• HVAC blower control
• LK/CYL relay control
• Park brake relay control
• Rear defog relay control
• Rear park assist chime control
• Retained accessory power (RAP) relay control
• Reverse relay control
• Transmission shift inhibit
• Trunk release relay control
• Various controls for the interior lamps

Just looking at fuse's and relay's isn't enough ! Hooking up a factory scan tool an checking for DTC'S - diagnostic trouble codes in all the vehicle control modules is always the first step . Which fuse boxes did you check ? Do you know there is a fuse box under the back seat ?
Fuse Block - Rear
Left rear of the passenger compartment, under the rear seat !
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door, but the rear integration module (RIM), which is the master control for the door lock system, determines when the lock functions are permitted. The RIM receives and examines the requested lock function from the individual door modules, or from the remote function actuator (RFA) via the class 2 serial data circuit. The RIM also examines the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. If the RIM determines that a lock or unlock function is permitted, it sends a class 2 message back to the individual door modules commanding them to perform that Lock or Unlock function.
Your best bet , take it to the dealer !

Jun 06, 2017 | 2003 Cadillac Seville STS

1 Answer

2005 Chevrolet Tahoe Power Windows and Power Locks not working.


The power windows an power locks are controlled by a module , DDM - driver door module . As far as the locks locking when you put the vehicle into reverse an unlocking when you put the vehicle into park , that's how there are suppose to work , automatic lock an unlock feature . When you put the vehicle into any gear from park the locks should lock . Did she hit window lockout function ?

The power door lock system consists of the following components:
• The driver door module (DDM)
• The passenger door module (PDM)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock switch
• The door lock relay
• The door unlock relay
• The liftgate lock relay--utility vehicles with liftgate only
• The reversible door lock actuators in each of the doors and liftgate
• LOCKS 20A fuse (rear lock/unlock relay supply voltage)
• ECC 10A fuse (liftgate lock relay supply voltage .

Programmable Automatic Door Locks
The automatic door lock feature can be programmed to control the door lock system. The automatic door lock feature is factory programmed to have all doors lock and unlock. For detailed instructions on programming the automatic door locks, refer to Vehicle Personalization in Personalization.
When the automatic door lock feature is programmed to control the door lock system, the driver door module (DDM), passenger door module (PDM) and body control module (BCM) will lock the vehicle doors if the following inputs are true:
• Ignition 1 input is active.
• All door jamb switch inputs are inactive.
• Cargo door or liftgate/liftglass ajar inputs are inactive.
• Transmission is shifted out of park.
This automatic door lock function will only occur once per ignition cycle unless, a door jamb switch input changes state to active and back to inactive. Then the DDM, PDM and BCM will lock all doors again.
Once the automatic door lock feature has locked the doors, the BCM will then unlock all the doors when the transmission is shifted into park.
Driver, Passenger and Cargo Door Lock System Operation
The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
• The DDM (driver door lock actuator).
• The PDM (passenger front door lock actuator).
• The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

Mar 16, 2017 | 2005 Chevrolet Tahoe

1 Answer

I have power to the door lock switches on the drivers door but the locks do not work nor does the back hatch or the switch at the back hatch that controls all the locks in the vehicle. Do the locks g


Power Door Locks Circuit Description
The power door lock system incorporates door lock switches on both front doors and on the RH D-pillar, door lock motors in all passenger doors and in the RR cargo door, a door lock relay and a door lock control module.
Power for the door lock switches and the door lock control module is supplied from the CIG LTR fuse 13 through CKT 640 (ORN). Power for the door lock relay is supplied from the PWR ACCY circuit breaker through CKT 540 (ORN). Ground for the door lock relay is supplied from G202 through CKT 150 (BLK) and ground for the door lock control module is supplied from G400 through CKT 150 (BLK).
The door lock motors are reversible and both sides are connected to the normally closed contacts of the door lock relay. Those contacts of the relay are connected to G202. When any of the door lock switches are placed in the lock position, voltage is supplied through CKT 195 (LT BLU) to the relay lock coil. Since the other side of the lock coil is connected to ground, the coil is energized and it pulls the lock contacts closed. Voltage is then supplied through CKT 295 (GRY) to all the door lock motors and the doors lock. The unlock function operates in much the same manner except that when any of the switches are placed in the unlock position, voltage is supplied through CKT 194 (WHT) to the unlock coil of the relay and CKT 294 (TAN) supplies voltage to the apposite side of the door lock motor and the doors unlock.
Door Lock Control Module Description
The door lock control module is used on vehicles equipped with cargo doors. The purpose of the module is to lock the cargo doors after a lock cycle has been commanded from any of the door lock switches with the cargo doors open. When the RH cargo door is open, the module receives a ground signal from the closed contacts of the rear door jamb switch on CKT 1897 (ORN/BLK) to G400. When a lock command is received, the module retains this input until it receives an open input from the rear door jamb switch. Then the module sends a lock command through CKT 194 (WHT) to the door lock relay and the doors lock.
Rear Cargo Doors Description
The power door lock motor will not operate unless the rear cargo doors are fully closed. The power door lock motor is in the right cargo door. The contactors are on the rear cargo door opening on the body and on the right cargo door.

May 23, 2017 | 1997 GMC Yukon

2 Answers

My rear door auto lock is not working


Does that doors' lock get any power when you hit the button to lock? You may have to check the wiring going to the door and search the internet to find out what wire gives power to the lock.

Mar 15, 2009 | 1994 Lexus GS 300

1 Answer

Power door locks on rear doors do not open


The rear doors have a separate relay for the lock and unlock function. There's a good chance the unlock relay is bad. The relays in question are located in the left instrument panel fuse block. Hope this helps

Oct 10, 2008 | 2003 Chevrolet Silverado 2500HD

1 Answer

Single power door lock does not work


If it doesn't work from master switch then the door lock motor actuator will need to be replaced, this requires pulling the door panel.

Sep 20, 2008 | 2003 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...