Question about 2000 Toyota ECHO

1 Answer

No brake fluid going to right front wheel - 2000 Toyota ECHO

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Collapsed brake hose

Posted on Sep 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I was wondering if I would be able to replace a right front brake line on my own or if I should take it to a mechanic?

you can do this on your own...did you break the front brake line? if it's the hard metal line, you can go buy it at the parts store...If it's the rubber line, you can buy that there too...if you do it yourself, get the right wrench for the job, ask the parts store for it. If not, you will strip the nuts and won't be able to get the lines off. First thing, loosen the lug nuts on the right front wheel, then just jack the car up and put it on jackstands with the rear wheels "chocked" so they can't roll backwards. Put on your ebrake too. then get the old brake line out, and replace it with the new one. make sure you clean up the brake fluid that got all over the place while you do this. Once you have the new line in place, go to your brake resevoir, fill it up to the "full" line and then go back to the right front wheel hub. There you will find a "bleeder screw" with a rubber cap on it usually. take the cap off if it is there and again with the appropriate tool, open the bleeder screw counterclockwise until brake fluid flows out of it easily. Then have someone sit in the car and pump the brakes a few times slowly and on the third or fourth pump, have them hold it down and close the bleeder screw so that no fluid is coming out. Then have them release the pedal. Now the fun part, go to the rear LEFT wheel and do the same "bleed" process. Why? Because the Front Right and Rear Left wheels are part of the same Line. Brake systems are made this way in case one of the cylinders in the master cylinder fails, half of your cars brakes will still work. Make sure you check the fluid and fill as necessary along the way so that the master cylinder doesn't run dry. Once you have repeated the process for bleeding all of the wheels, fill the fluid up again, make sure the wheels are all on tight, drop the car back down, start the car, pump the brakes a few times and take it for a test drive. The time to do this depends on your abilities and patience. If it's you and a friend, maybe about an hour if you take your time. Parts wise...somewhere around 15 bucks for the front brake hose, or around 10 bucks for the brake line...then factor in the fluid (get the big bottle just in case), and the tools and you can probably do this for about 50 bucks...a shop would probably triple this price. Let me know how it went!

Jul 03, 2012 | 2001 Kia Sephia

1 Answer

How to drain brake fluids on toyota camry 1998

First of all your going to need a bleeder wrench to open the bleeder valves located on your brake calipers correctly without crushing or damaging the nipple. First make sure the brake fluid is at the max capacity in the master cylinder. Then have someone pump the brakes several times and keep pressure of them whie you loosen first the Right Rear, then Left Front then Left Rear then right front. As you move from wheel to wheel don't forget to tighten the wheel your currently working on first. Keep doing this sequence until the brake fluid is coming out clean and with no air bubbles. Don't forget to fill the master cylinder bake to max full. You may have to pump your brakes until firm before driving just to be on the safe side.

Jun 27, 2012 | 1998 Toyota Camry

1 Answer

Why do brakes go to floor but still have light pressure?

It sounds like you have air in your brake lines. This is usually caused by a very low brake fluid in the master cyclinder.
To fix this problem fill up the master cyclinder with brake fluid and bleed the front wheel brake cyclinders until the air bubbles are removed. Keep the master cyclinder topped up with brake fluid. Then bleed the rear wheel brake cyclinders until the air bubbles are removed. Don't forget to top up the brake fluid in the master cyclinder.

Dec 31, 2011 | 2004 Chevrolet Cavalier

1 Answer

How to bleed brakes on 2002 toyota sienna

Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order

  1. right rear wheel
  2. left rear wheel
  3. right front wheel
  4. left front wheel

HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.

NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.


b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.

Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.


1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.

CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3

Jun 25, 2010 | 2002 Toyota Sienna

1 Answer

2007 Santa Fe. Brake lights and battery light come on when steering wheel is turned hard to the lef tor to the right. Lights go off when wheels pointed straight ahead. Rough sounds from motor. Very hard to...

There are a number of problem mentioned on the internet about brake problems and brake calipers seizing up. Smoke and smell from the right front wheel might lead a person to believe there is the best place to start looking.

Dec 23, 2017 | 2006 Hyundai Santa Fe

1 Answer

Proper way to bleed brakes on 2004 chevy impala

To bleed brakes on your particular vehicle is the same as it's been for Years. Start at the wheel furthest away from the Master Cylinder. (a helper is needed to do this unless you have a pressurized brake bleeding unit). Start the car and have someone pump the brake up about ten times and hold the brake pedal down. Then at your right rear wheel, open the bleeder and allow the air and brake fluid to squirt out. Close the bleeder while your helper still has his foot on the brake and repeat until nothing but brake fluid comes out...then move to your left rear, right front and finally left front doing the same thing. Between going to another wheel, have your helper check the master cylinder's fluid level for if it goes dry during your bleeding operation, then you'll just be putting air back into the system. A couple of words of caution here...the first is that brake fluid is highly corrosive to paint, so make sure you immediately wipe it from painted surfaces and number two: DO NOT USE$ OLD BRAKE FLUID WHILE PERFORMING THIS OPERATION! Brake fluid has a quality about it that it absorbs moisture from the air...or the humidity. In this case, you're introducing water into your brake system which means all metal parts in your braking system that's in contact with this poor mixture will eventually fail due to rust. Yes, rust will form from old brake fluid with moisture in it and can cause a metal piston in a brake caliper to "freeze" causing a violent jerking of the wheel when applying brakes normally while driving. ALWAYS use fresh brake fluid (unopened), when performing a job such as this.

Hope this Helps,


"Still living on the Right Side of Dirt..."

May 18, 2010 | 2004 Chevrolet Impala

2 Answers

I have re/re the rear brake cylinders,shoes,drums,front rotors,pads,and callipers on my 2000 gmc safari van.i have bled all the brakes. but the drivers front has no pressure or fluid.the other three brakes...

make sure you are bleeding them by doing them as an abs system,do the right rear then the left front,then the left rear then the right front,the opposite wheels are how the system brakes.

Jan 21, 2010 | 2000 GMC Safari

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer

Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

2 Answers

Brake line leak

start from the farthest, right rear, left rear, right front, then left front, take some time in bleeding your left front since it has more air induced during line replacement. good luck!

Oct 20, 2008 | 1990 Acura Legend

3 Answers

Did a brake job on all 4 wheels and changed master cylinder, but still have a low brake pedal

You have air in the brake hydraulic system, to bleed the brakes properly do this, go to the right rear wheel and have some one pump the brake pedal at least ten times, then ope bleed valve at back of wheel cylinder, do this until you hear a spitting sound, which indicates air, do this at every wheel in this order, RR, LR, RF, LF. check the Master cylinder reservoir each time you do a wheel and top it off. If you make a mess brake fluid washes off with water, don't get it on any painted surface, it will take the paint off. Hope this helps.

Jul 30, 2008 | 1997 Chevrolet Venture

Not finding what you are looking for?
2000 Toyota ECHO Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides